FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   -3.3. Motor of V6
      3.3.1. Technical characteristic
      3.3.2. The repair that does not demand the removal of the motor
      3.3.3. Removal of the motor
      -3.3.4. To be demolished and check of details of the motor
         3.3.4.1. Desmontagem of the motor
         3.3.4.2. Check of degree of use of details of the motor
         3.3.4.3. Knot of an axle of yokes
         3.3.4.4. Empurradores of valves and bar of empurradores
         3.3.4.5. Axle
         3.3.4.6. Leaders of the cylinder block
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and rings of piston
         3.3.4.9. Fingers of piston and sticks
         3.3.4.10. Inclination end
         3.3.4.11. Radical loads and conrod
         3.3.4.12. Distributive gear wheels
         3.3.4.13. Pendulum
         +3.3.4.14. Lubrication system
         3.3.4.15. System of ventilation of a case
         -3.3.4.16. Meeting of the motor
            3.3.4.16.1. Installation of an end of inclination
            3.3.4.16.2. Installation of the axle
            3.3.4.16.3. Installation of pistons and sticks
            3.3.4.16.4. Installation of the bomb of oil
            3.3.4.16.5. Installation of a pendulum
            3.3.4.16.6. Installation of a wheel of gear and covering of the walk of the distributive mechanism
            3.3.4.16.7. Installation of the trundle bed of oil, water bomb and pulley of the axle of crank
            3.3.4.16.8. Removal and installation of the conductor of heat of oil
            3.3.4.16.9. Leaders of the cylinder block, axes of yokes and collector of entry
         3.3.4.17. Agreement of slits of valves
         3.3.4.18. Auxiliary details of the motor
         3.3.4.19. Installation of the motor
         3.3.4.20. Launch of the motor after repairs of capital or restoration
      +3.3.5. Modifications in a drawing of motors V6 2,4 and 2,9 dm3
   +3.4. Systems of ignition and management of motor
   +3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

3.3.4.16.6. Installation of a wheel of gear and covering of the walk of the distributive mechanism

ORDER OF REALIZATION

1. To establish a new hunting they touch a walk covering.
2. To check flutes shponochny in the end of an end of inclination, they will be pure, in splines must not be an agnail. To establish splines in flutes shponochny.
	3. If the wheel of gear of an end of inclination was withdrawn, to establish it at the place so that the gear wheel up to the end was established in an inclination end, at the same time it is possible to use a tube of the convenient diameter. To hold tight it also it is possible to use a pulley and a pin temporarily.
	4. To establish a wheel of gear of axle in an end so that the etiquette went for a nucleus with an etiquette in a wheel of gear of an end of inclination. Pay the attention what in a wheel of gear of the axle of crank there are two etiquettes done a nucleus it is necessary to carry out the coincidence to the necessary etiquette. At the same time the grooves of shponochny become one to other. In 2,4 and 2,8 motors dm3 subsequent to wheel of gear from nylon of the axle it is established.
5. To establish a lavador and a pin of a wheel of gear of the axle. To hold tight a pin according to the moment of inhalation.
6. To compensate for an advanced surface of an intermediary plate and the inter-connected walk they cover the surface, soon to apply the selante in both inter-connected surfaces.
7. To establish the new placing in an intermediary plate and to install a covering of the walk of the distributive mechanism in the cylinder block.
8. To establish pins of fixation of a covering of the walk and to hold tight them according to the moment of inhalation.
	9. To check a play of axial side of the axle.
	10. To define the provision of a hunting they touch a covering of the distributive mechanism, soon to pinch to had been an old consolidation.
11. To compensate for the advanced airplane of a transitional plate and the airplane of a covering of the distributive mechanism, soon to cover both surfaces of the selante.
12. To put the new placing in a transitional plate and to establish a covering of the distributive mechanism in the cylinder block. Pins wrap up manually.
	13. Having used a beat of calibre, to center a covering of the distributive mechanism about the axle, up to the end to hold tight pins.
	14. Establish a ring of fighter in a covering of the distributive mechanism and to insert it at the place, through the capture and a pin.
	15. Withdraw edges of placing of the connected surfaces of a case of oil.