FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   -3.3. Motor of V6
      3.3.1. Technical characteristic
      3.3.2. The repair that does not demand the removal of the motor
      3.3.3. Removal of the motor
      -3.3.4. To be demolished and check of details of the motor
         3.3.4.1. Desmontagem of the motor
         3.3.4.2. Check of degree of use of details of the motor
         3.3.4.3. Knot of an axle of yokes
         3.3.4.4. Empurradores of valves and bar of empurradores
         3.3.4.5. Axle
         3.3.4.6. Leaders of the cylinder block
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and rings of piston
         3.3.4.9. Fingers of piston and sticks
         3.3.4.10. Inclination end
         3.3.4.11. Radical loads and conrod
         3.3.4.12. Distributive gear wheels
         3.3.4.13. Pendulum
         +3.3.4.14. Lubrication system
         3.3.4.15. System of ventilation of a case
         -3.3.4.16. Meeting of the motor
            3.3.4.16.1. Installation of an end of inclination
            3.3.4.16.2. Installation of the axle
            3.3.4.16.3. Installation of pistons and sticks
            3.3.4.16.4. Installation of the bomb of oil
            3.3.4.16.5. Installation of a pendulum
            3.3.4.16.6. Installation of a wheel of gear and covering of the walk of the distributive mechanism
            3.3.4.16.7. Installation of the trundle bed of oil, water bomb and pulley of the axle of crank
            3.3.4.16.8. Removal and installation of the conductor of heat of oil
            3.3.4.16.9. Leaders of the cylinder block, axes of yokes and collector of entry
         3.3.4.17. Agreement of slits of valves
         3.3.4.18. Auxiliary details of the motor
         3.3.4.19. Installation of the motor
         3.3.4.20. Launch of the motor after repairs of capital or restoration
      +3.3.5. Modifications in a drawing of motors V6 2,4 and 2,9 dm3
   +3.4. Systems of ignition and management of motor
   +3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

3.3.4.16.3. Installation of pistons and sticks

ORDER OF REALIZATION

1. To rub stocking of a stick in a covering and the lowest part of an insertion and to establish at the place an insertion so that the agreement uvula entered in the corresponding interruption of a stick.
2. If the insertions are not modified in the new, to follow the trace of this they were established at ancient places to the corresponding sticks.
3. The pistons with sticks are installed in the corresponding cylinders of above mentioned of the cylinder block.
4. To arrange locks of the piston touches how if it follows: – I come across: 150 ° in a party of an union of a spiral dilator of a ring of scraper of oil; – central office: 150 ° in another party of an union of a spiral dilator of a ring of scraper of oil; – more low: a spiral dilator of an oil scraper touches in front of the notable hall of the party of the piston; – ring of scraper of oil, intermediary rings: 25 mm of each party of a slit of a spiral dilator.
5. To the oil the piston and the piston touch the motor.
6. To install the universal device of the compression of the piston touches and to be prepared for the installation of the first piston in the cylinder. To check: the conrod and the groups of piston will correspond to numbers of cylinders, the stick has to be established in the right direction, an advanced part of the piston has to be installed to an advanced part of the motor (in the bottom of the piston there is corresponding arrow or an etiquette).
	7. To polish a skirt of the piston and to insert conrod and group of piston in an opening of cylinder so that the lowest part of the device of the compression of rings of piston was installed in the cylinder block.
8. Carefully, but strongly to slam with the hammer they negotiate in the piston to install the piston in the cylinder.
9. To the oil conrod driving of necks and to become an end of inclination so that the necks conrod fell in the most comfortable position of the installation of sticks in them.
10. To rub a covering of the load of a stick and the exterior side of an insertion and to establish insertions at the place so that the uvula of agreement of an insertion entered in an agreement flute in a stick covering.
11. To polish the load and to establish a covering in a stick.
12. To establish to the place of a nut of stick.
13. A dynamometer key holds tight nuts according to the moment of inhalation.
14. When are all the sticks established at the place, to become an end of inclination in order that to be secured what the end spins freely, without interference.