FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car



Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   -3.3. Motor of V6
      3.3.1. Technical characteristic
      3.3.2. The repair that does not demand the removal of the motor
      3.3.3. Removal of the motor
      -3.3.4. To be demolished and check of details of the motor
         3.3.4.1. Desmontagem of the motor
         3.3.4.2. Check of degree of use of details of the motor
         3.3.4.3. Knot of an axle of yokes
         3.3.4.4. Empurradores of valves and bar of empurradores
         3.3.4.5. Axle
         3.3.4.6. Leaders of the cylinder block
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and rings of piston
         3.3.4.9. Fingers of piston and sticks
         3.3.4.10. Inclination end
         3.3.4.11. Radical loads and conrod
         3.3.4.12. Distributive gear wheels
         3.3.4.13. Pendulum
         +3.3.4.14. Lubrication system
         3.3.4.15. System of ventilation of a case
         -3.3.4.16. Meeting of the motor
            3.3.4.16.1. Installation of an end of inclination
            3.3.4.16.2. Installation of the axle
            3.3.4.16.3. Installation of pistons and sticks
            3.3.4.16.4. Installation of the bomb of oil
            3.3.4.16.5. Installation of a pendulum
            3.3.4.16.6. Installation of a wheel of gear and covering of the walk of the distributive mechanism
            3.3.4.16.7. Installation of the trundle bed of oil, water bomb and pulley of the axle of crank
            3.3.4.16.8. Removal and installation of the conductor of heat of oil
            3.3.4.16.9. Leaders of the cylinder block, axes of yokes and collector of entry
         3.3.4.17. Agreement of slits of valves
         3.3.4.18. Auxiliary details of the motor
         3.3.4.19. Installation of the motor
         3.3.4.20. Launch of the motor after repairs of capital or restoration
      +3.3.5. Modifications in a drawing of motors V6 2,4 and 2,9 dm3
   +3.4. Systems of ignition and management of motor
   +3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment


bfe6b27a


3.3.4.16. Meeting of the motor

GENERAL INFORMATION

In order that motor carries out the very useful life of then the capital repairs at problems least is necessary not only to join correctly all the details, but all the details and the component ones will be perfectly pure, all the lubricating channels will be pure, the lock and the spring lavadores are established at the place. The loads and other details that have the surfaces of the unstable necessity to be polished carefully during the meeting.

Before to begin the meeting, to substitute with new pins, hair clips of hair and nuts which woodcarvings are damaged whenever possible also it is necessary to substitute with new spring lavadores.

In the installation time for glance that the details established at ancient places, also to check the direction of the installation. The edges of consolidations of oil before the installation must be polished. During the installation of putting not to allow the hole, to use where if it needs, selante.