Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+ 10. Supports of the triangular form of interruption
- 11. Brakes system
11.1. Technical characteristic
+11.2. Dispatch brakes
+11.3. Subsequent brakes
11.4. Agreement of the brake of emergence
11.5. Removal of air of the system of brakes
+11.6. System antiblockade
+12. Wheels and tires
+13. Body
+14. Electric equipment
|
The work brake with the system antiblockade puts itself in the action for the hydraulic double circuit cylinder of main brake (type a tandem) and the auxiliary device besides hydraulic that.
The hydraulic outlines of the halls the brakes (right and left) are divided and address for the cylinder of main brake. The subsequent brakes (in the system "Y") drive for the hydraulic auxiliary device.
The emergence brake puts itself in the action mechanically and puts brakes back in the action.
Dispatch brakes
Dispatch the disc of brakes. In them the ventilated discs, and also the supports float with a piston if they use.
| Exterior diameter of a disc of brake |
260 mm (cars with the motor of 2,9 l 24V - 278 mm)
|
| Disc thickness: |
| – nominal |
24,05 mm
|
| – admissible minimum |
22,2 mm
|
| The very blows of a disc |
0,15 mm
|
| Diameter of the cylinder of a support |
60,0 mm
|
| Type of shoes of brake |
Ferodo of 343 25 FF
|
| Blocks sizes |
38 x 111 mm
|
| Mistakes thickness (without basic plate): |
| – nominal |
18,0 mm
|
| – admissible minimum |
one defines removing of a flute in surfaces of a shoe of brake
|
Subsequent brakes
Subsequent brakes disc. In them full discs, and also the supports float with a piston if they establish.
| Support: |
| – mark and type |
Ford L2 9024
|
| – diameter of the piston |
43 mm
|
| Disc: |
| – exterior diameter |
252,7 mm (cars with the motor of 2,9 l 24V - 272 mm)
|
| – thickness: |
| • nominal |
10,1 mm (in the cars of Turnier and with motors of 2,9 l 24V - 20 mm)
|
| • nominal admissible |
8,9 mm (in the cars of Turnier and with motors of 2,9 l 24V - 18 mm)
|
| – the very blows of a disc |
0,15 mm
|
| Brake shoes: |
| – mark and type of blocks |
GIFT 8106/1
|
| – nominal thickness |
13,5 mm
|
| – nominal admissible thickness |
one defines removing of a flute in surfaces of a shoe of brake
|
System of the walk
The system putting a brake of work in the action is hydraulic, there contains the double circuit cylinder of main brake and the hydraulic auxiliary device, and also system antiblockade.
| Mark |
ABS Teves MK II, with 04,1992 – ABS Teves MK IV
|
| Device of electronic actuation |
Teves
|
| Resistance of the sensor of speed of rotation of a wheel |
0,8 - 1,4 Ohms
|
| Control pressure |
4 - 9 MPas
|
| Pressure of operation of the valve of security of system |
21 MPas
|
Brake fluid
| Quantity |
1,4 dm3
|
| To type |
Fluid of brake of Ford SAM 6C 9103 To
|
| Substitution frequency |
each one 60.000 km or time during two years
|
Cylinder of main brake
In a cavity of the main cylinder two pistons are located constantly, each one of which makes working the outline.
| Mark |
Bendix or Up to
|
| Pistons diameter |
22,0 - 22,2 mm
|
Amplifier of vacuum of brakes
The amplifier of vacuum of brakes influences the cylinder of main brake and contains a diaphragm.
The operational diameter: 227 mm.
Pressure regulator
The regulator of the pressure is installed in the oil pipeline of rear brakes and the force of limit of the frenagem of rear wheels.
Moments pressure
| Support arm to a rotary fist of a wheel |
65 - 75 nanômetros
|
| Fixation of a support of a brake advanced to an arm |
31 - 35 nanômetros
|
| Fixation of the bearer of a support of a rear brake |
51 - 61 nanômetros
|
| The fixation of a support of a few back brakes to the direction finger |
51 - 61 nanômetros
|
| Fixation of hydraulic knot of management to a splitting frontlet |
41 - 51 nanômetros
|
| Fixation of the hydraulic accumulator to the brake cylinder |
34 - 46 nanômetros
|
| Fixation of the cylinder of brake |
70 - 90 nanômetros
|
| Fixation of captures (Banjo) of oil pipelines of high pressure |
16 - 24 nanômetros
|
| Fixation of the bearer of a tank of fluid of brake |
40 - 60 nanômetros
|
| Fixation of the sensor of speed of rotation of a wheel |
85 - 110 nanômetros
|
| Deaerator, as much as possible |
10,5 nanômetros
|
| Nut of fixation of a wheel |
100 nanômetros
|
|
|
