FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   -3.3. Motor of V6
      3.3.1. Technical characteristic
      3.3.2. The repair that does not demand the removal of the motor
      3.3.3. Removal of the motor
      -3.3.4. To be demolished and check of details of the motor
         3.3.4.1. Desmontagem of the motor
         3.3.4.2. Check of degree of use of details of the motor
         3.3.4.3. Knot of an axle of yokes
         3.3.4.4. Empurradores of valves and bar of empurradores
         3.3.4.5. Axle
         3.3.4.6. Leaders of the cylinder block
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and rings of piston
         3.3.4.9. Fingers of piston and sticks
         3.3.4.10. Inclination end
         3.3.4.11. Radical loads and conrod
         3.3.4.12. Distributive gear wheels
         3.3.4.13. Pendulum
         +3.3.4.14. Lubrication system
         3.3.4.15. System of ventilation of a case
         +3.3.4.16. Meeting of the motor
         3.3.4.17. Agreement of slits of valves
         3.3.4.18. Auxiliary details of the motor
         3.3.4.19. Installation of the motor
         3.3.4.20. Launch of the motor after repairs of capital or restoration
      +3.3.5. Modifications in a drawing of motors V6 2,4 and 2,9 dm3
   +3.4. Systems of ignition and management of motor
   +3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

3.3.4.6. Leaders of the cylinder block

GENERAL INFORMATION

Play entry (in top) and final valves

Consolidation entry (in the left) and final valves

ORDER OF REALIZATION

1. To withdraw the oil and the leaders' dirt of the cylinder block. To remove a deposit of cameras of combustion and leaders of valves through a scraper or the rotating metal brush.

2. To hold tight springs valvate through the corresponding device of the spring compression valvate and to withdraw fine cookies of valves. To withdraw the device of the spring compression valvate and to withdraw a plate of one spring valvate, one spring and the valve. To mark each valve subsequently to establish at the ancient place.

3. After the valves removal to withdraw a deposit of walls of channels.

4. To check plates of valves and a saddle of the existence of a vykrashivaniye and obgoraniye. The aspects of a boy vykrashivaniye in the valve and a saddle of the valve can be removed grinding in in the beginning with it of thick granulation, and grinding briefcase soon of fine granulation. In scars vykrashivaniye the valves will be a land in the machine to grind of valves and a saddle in the machine to grind of valves saddles. For the realization of two last types of works it is necessary to direct experts.

5. To check guides of valves of the existence of use: to insert the valve in a guide, the valve in a guide has to move easily, without side slit. The special instruments, therefore, it is necessary to direct experts they are necessary for the substitution of guides used by the new.

6. The grinding in from valves has to be done with the use alone of the briefcase of polishing of fine granulation.

7. Quantity of briefcase to polish a surface of a saddle of the little valve with an and to install the valve in the corresponding saddle. To hold tight densely to a plate of the valve a cupping glass of rubber and to make spinning the valve in one or another party.

8. After the end of the process of the grinding in carefully for compensating for all the details of dirt and briefcase and to check a saddle and a plate of the valve. The continuous opaque ring in both details that specifies the width of facet of valve will be visible.

9. To check springs valvate the effort of the compression and the spring length without load.

10. To the oil a motor of nucleus of valve and to establish in a valve guide. To establish the new consolidation.

11. To establish one spring valvate and a plate of one spring valvate.

12. Through the corresponding device of the spring compression valvate to hold tight one spring so that the fine cookies were established in grooves in a valve nucleus. To withdraw the adaptation.

13. After the installation of all the details at the place, lightly to slam with the hammer with the lively plastic of when springs were above mentioned valvate to it be convinced what the fine cookies established at the place.