1. To fuse the oil in the corresponding container (if one did not do before). |
2. To unscrew a filter of oil through the key of chain or a belt. |
3. To take the probe of the measurement of the level of oil. |
4. In some cars models to unscrew through a pull in the 37 mm nut for special offer that the arm that is lengthened fixes to the oil heater. To withdraw an arm together with lavadores and a fighter ring. To unscrew the central capture and to withdraw the heater of oil together with the placing. |
5. To withdraw the union. To pay attention to the provision of the installation of a plate of pressure. |
6. To withdraw basic arms of the motor. |
7. To withdraw the bomb of the amplifier of the direction and a belt of driving. |
8. To unscrew a pin of the fixation of a flange of pressure of the distributor of the ignition and to take the distributor of the cylinder block. |
9. To unscrew two pins that the arm of the only pulley of a belt of driving of the bomb of the amplifier of the fixed direction to the superior covering and to withdraw an arm and a pulley. |
10. To weaken pins of the fixation of the creator of the alternate current and to lift the creator, to take away a supporter's belt. To unscrew three pins that the basic arm of the creator of the fixed alternate current to the cylinder block and to remove the creator of an arm. |
11. To withdraw the ventilator and a pulley of the water bomb. |
12. Desconectar a line of supply of fuel of the carburator and to withdraw the valve of the ventilation of a case (if it is established) of a covering of a head of the cylinder block. |
13. To weaken collars of fixation and desconectar a hose of the union of the water production and to go round a hose of the case of thermostat. |
14. To unscrew four pins of the fixation, to withdraw the carburator and an intermediary flange of a collector of entry. |
15. To unscrew pins of coverings of a head of the cylinder block and to discover. |
|
|
16. To unscrew pins of fixation of axes of yokes valvate and to move axes (the drawing in the left) and you guard of maslootrazhatelny (the drawing on the right). Pay attention to the direction of the policemen's installation. To apply etiquettes in yokes axes valvate of the subsequent installation at ancient places. |
|
17. To withdraw bars of empurradores. put them in the corresponding yokes axes valvate, for the installation repeated at ancient places. |
18. To unscrew pins of fixation of entry and final collectors and to remove collectors. Since during the installation of a collector's selante of entry it is in use, there is necessary a collector uses the screwdriver for desconectar, nevertheless, never to have the screwdriver between surfaces of contact of a collector of entry and the cylinder block. |
19. To unscrew constantly pins of the fixation of a head of the cylinder block; the order to unscrew of pins will be the return to an order of his pressure. |
20. To remove leaders of the cylinder block. If the head is not removed, it is necessary to break the entirety of the consolidation between the cylinder block and a head, having knocked down a head. If it does not help, it is possible to try through sharp punches for the hammer with a part of gentle shock to set a head free. Not to hit with the metal hammer straightly a head in absolute: it can destroy the fragile throw. Also it is impossible to separate a head, inserting the screwdriver or a chisel between him and I eat the cylinder block at the same time it is possible to damage the inter-connected surfaces of these details. |
21. To withdraw the leaders' placing of cylinders. |
22. To unscrew two pins that the fixed fuel bomb to the block, soon to withdraw the bomb, placing and sketch of the transfer of lever. |
23. To unscrew and to withdraw the sensor of pressure of oil. |
24. To unscrew a pin that the pulley of an end of fixed inclination and to withdraw a pulley. If the pulley concentrates on a fluctuations damper, also to unscrew the central pin of a damper. |
25. To observe the provision of a pendulum of somewhat the end of inclination subsequently to establish in the same situation. |
26. To blockade a pendulum, soon to unscrew six pins that the pendulum fixes to an inclination end and to withdraw a pendulum. |
27. To withdraw a rear plate of the motor. |
|
|
28. To install the motor in an end face and through a wire of bent copper (to see the rice. The bent wire of the extraction of empurradores of valves) to take empurradores of valves. To put empurradores in the corresponding bars of empurradores subsequently to establish in ancient openings.
|
29. To unscrew pins of the fixation of the trundle bed of oil and to withdraw the trundle bed and the placing of the trundle bed. |
30. To unscrew a tube of reception of the bomb of oil and to withdraw the placing. |
|
|
31. To unscrew two pins (they are specified by firearms in the drawing in the left) and to withdraw the bomb of oil. The oil bomb withdraws an end of power (it is specified by an arrow in the drawing on the right), having paid attention to the provision of the installation.
|
|
32. To discover a case of union. |
33. To unscrew a tube of rear branch of the thermostat of the system of cooling. To withdraw the placing. |
34. To unscrew pins that the water bomb fixes to a covering of the walk of the distributive mechanism and to withdraw the water bomb. |
35. To unscrew pins of case of thermostat, to withdraw the case and to take the thermostat. Desconectar a tube of rear branch of the water road. |
36. To unscrew pins that the covering of the walk of the distributive mechanism fixes to an advanced part of the cylinder block and to discover. |
37. To withdraw consolidations to cancel what are not subject to the reuse. |
|
38. To unscrew a pin that the wheel of fixed gear of the axle to the axle and to withdraw a wheel of gear. |
|
39. To unscrew pins of fixation of an advanced intermediary plate and to withdraw an intermediary plate. |
|
40. To unscrew two pins of fixation of a persistent flange of the axle and to take the axle together with a persistent ring, soon to withdraw one spring lamellar and placing. |
41. If it is necessary to withdraw a wheel of gear of an end of inclination, using an artist of streaptise usually for the removal. |
|
|
42. To check the identification marks in loads coverings conrod and you pierce (the drawing in the left) to be secured from the coverings complaisance to sticks and subsequently to establish groups of details of appropriate places. In the pistons bottoms there are etiquettes (arrow) that indicates the advanced party (the drawing on the right). The firearms have to go to the bottom of the piston to an advanced part of the motor. |
43. To unscrew nuts of coverings of sticks and to arrange from a side in that order in which they acted. |
44. To discover sticks, to organize the storage in the appropriate order, having paid attention to the direction of the installation. Also in order that it follows the trace what it inserts if they supplied with the corresponding sticks if they are not only subject to the substitution. If the sticks are not discovered, to hit lightly them with the hammer with the gentle living creature. |
|
45. To withdraw an insertion, hold tight it in front of a flute in a stick and a covering, the insertion is going to be withdrawn easily. |
46. To push with the hammer doorknob of down, takes the piston and a stick of the cylinder. |
|
47. To check that in radical loads it is etiquettes of identification that they allow to establish them in the necessary provisions in the meeting. In loads coverings his numbers (they are specified by arrows A and B) are abolished, and the arrow indicates an advanced part of the motor. It must be noticed that in the covering driving 2,8 l with the numbers 2 and 3 fixes longer pins with convex heads. |
48. To unscrew pins of the fixation and to discover radical loads and the lowest insertions; the insertions must be supplied with the corresponding coverings. |
49. In the moment of the removal of a covering of the back the radical load to remember that the ring of rear fighter of an end of inclination also is guarded by him. |
50. In the moment of the removal of a covering of the radical load n ° 3 in order that persistent rings half pays attention to an agreement of two. |
51. To take an end of inclination of a case and to withdraw a ring of rear fighter. |
52. 3 of a case to take the lowest insertions of radical loads and the superior persistent half of the rings of the load n °, to arrange them for the storage with the corresponding coverings of radical loads. |