FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   -3.3. Motor of V6
      3.3.1. Technical characteristic
      3.3.2. The repair that does not demand the removal of the motor
      3.3.3. Removal of the motor
      -3.3.4. To be demolished and check of details of the motor
         3.3.4.1. Desmontagem of the motor
         3.3.4.2. Check of degree of use of details of the motor
         3.3.4.3. Knot of an axle of yokes
         3.3.4.4. Empurradores of valves and bar of empurradores
         3.3.4.5. Axle
         3.3.4.6. Leaders of the cylinder block
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and rings of piston
         3.3.4.9. Fingers of piston and sticks
         3.3.4.10. Inclination end
         3.3.4.11. Radical loads and conrod
         3.3.4.12. Distributive gear wheels
         3.3.4.13. Pendulum
         +3.3.4.14. Lubrication system
         3.3.4.15. System of ventilation of a case
         +3.3.4.16. Meeting of the motor
         3.3.4.17. Agreement of slits of valves
         3.3.4.18. Auxiliary details of the motor
         3.3.4.19. Installation of the motor
         3.3.4.20. Launch of the motor after repairs of capital or restoration
      +3.3.5. Modifications in a drawing of motors V6 2,4 and 2,9 dm3
   +3.4. Systems of ignition and management of motor
   +3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

3.3.4.17. Agreement of slits of valves

GENERAL INFORMATION

Numeration of cylinders and connections of wires of high voltage

Valves agreement

The agreement of entry and final valves must be done in the cold motor in a temperature between 20 ° and 40 °C. The slits size valvate is very important for the realization of the best indicators of work of the motor. If the slit is too big, the valves will not open sufficiently, also they will confide late and to be closed early. If the slit is too small, the valves will not close completely what will lead to a lack of a compression and obgoraniye very quickly of valves and the saddles of the valves.

Agreement of slits of valves

During the agreement of slits of valves to become an end of inclination only in the motor course, to do the rotation, having established a key in a pulley pin.

ORDER OF REALIZATION

1. To become an end of inclination to combine an etiquette in a pulley of axle of crank with an etiquette in the form "is left" in a walk covering.

2. In the moment of the easy balance of a pulley ahead and it will be perceptible back that the valves of the cylinder n ° 1 or shake n ° 5 (two levers of the valve move in opposite directions). If the valves n ° mark 1 of cylinder with a diaeresis, to become an end of inclination in 360 ° what the valves n ° 5 of cylinder shook.

3. When 5 carried out the necessary position of valves of the cylinder n °, in order that there checks slits of valves of the cylinder n ° 1 so that it will install the probe of this or that thickness between the lever of the valve and a stick of the valve. A slit must be adjusted, turn the screw of agreement of the lever of the valve, the necessary size of a slit will not be still got. The slits of entry and final valves have size different.

4. Now, if an inclination end is turned in 1/3 turns, the valves n ° 3 of cylinder will shudder, and it is possible to check and 4 adjusts slits of valves of the cylinder n °.

5. To do the agreement of slits as ignition in cylinders as follows (to see the table). In rice. The numeration of cylinders and the connections of wires of high voltage to order of the numeration of cylinders are shown: the valves numeration happens regularly, from an advanced part of the motor (to see the rice. Valves agreement).

6. To establish the placing of coverings of the mechanism valvate and to establish coverings of the mechanism valvate. To hold tight pins of fixation according to the moment of inhalation.

Shake of valves	Adjustable valves
I press n ° 5	I press n ° 1 (entry, end)
I press n ° 3	I press n ° 4 (entry, end)
I press n ° 6	I press n ° 2 (entry, end)
I press n ° 1	I press n ° 5 (end, entry)
I press n ° 4	I press n ° 3 (end, entry)
I press n ° 2	I press n ° 6 (end, entry)