FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   -3.3. Motor of V6
      3.3.1. Technical characteristic
      3.3.2. The repair that does not demand the removal of the motor
      3.3.3. Removal of the motor
      -3.3.4. To be demolished and check of details of the motor
         3.3.4.1. Desmontagem of the motor
         3.3.4.2. Check of degree of use of details of the motor
         3.3.4.3. Knot of an axle of yokes
         3.3.4.4. Empurradores of valves and bar of empurradores
         3.3.4.5. Axle
         3.3.4.6. Leaders of the cylinder block
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and rings of piston
         3.3.4.9. Fingers of piston and sticks
         3.3.4.10. Inclination end
         3.3.4.11. Radical loads and conrod
         3.3.4.12. Distributive gear wheels
         3.3.4.13. Pendulum
         +3.3.4.14. Lubrication system
         3.3.4.15. System of ventilation of a case
         +3.3.4.16. Meeting of the motor
         3.3.4.17. Agreement of slits of valves
         3.3.4.18. Auxiliary details of the motor
         3.3.4.19. Installation of the motor
         3.3.4.20. Launch of the motor after repairs of capital or restoration
      +3.3.5. Modifications in a drawing of motors V6 2,4 and 2,9 dm3
   +3.4. Systems of ignition and management of motor
   +3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

3.3.4.18. Auxiliary details of the motor

ORDER OF REALIZATION

1. To support in the sensor of the water temperature and to corset itself according to the moment of inhalation.

2. To install the distributor and advanced corner adjusts an ignition.

3. To compensate for the surface of the cylinder block to contact to an oil filter, to the consolidation of oil of a filter of oil. To support in the new element of filtration so that the rubber consolidation was next to the block, soon to corset itself in 3/4 turns.

4. To support in the sensor of the pressure of oil and to hold tight it according to the moment of inhalation. To establish basic arms of the motor.

The motor with injection of fuel

5. To establish details of ancient places, glance that his initial agreement did not modify.

Carburator motors

6. To insert a stick of the fuel they pump in the cylinder block, to establish the placing of isolation, the bomb of fuel and fixation of pins.

7. To install the carburator.

8. There adheres a tube of a sapun of the motor to a covering of the mechanism valvate and a line of supply of fuel between the bomb of fuel and the carburator.

9. To do the installation of the automatic air door to the water to hose of union that gets a beating and a secondary passage they water with hose to the case of thermostat.

All the motors

10. To install the creator of the alternate current and to adjust a tension of a belt of driving.

11. To establish an arm of the only pulley of the bomb of the amplifier of the direction, having fixed it in an advanced part of the motor for two pins.

12. To install the bomb of the amplifier of the direction and to adjust a tension of a belt of driving.

13. To establish final collectors.