FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   +3.3. Motor of V6
   +3.4. Systems of ignition and management of motor
   -3.5. Diesel engines
      3.5.1. Technical characteristic
      3.5.2. The repair that does not demand the removal of the motor
      3.5.3. Check and adjust of valves slits
      -3.5.4. Fuel system
         3.5.4.1. Mouths
         3.5.4.2. Taken of incandescence
         3.5.4.3. Check of a compression
         3.5.4.4. Removal of air of system of fuel
         3.5.4.5. Removal and installation of the bomb of fuel
         3.5.4.6. Check and adjust of turns of wasting time
         3.5.4.7. Increase thread in turns of wasting time
      +3.5.5. Head of the cylinder block
      3.5.6. Removal and installation of the motor
      +3.5.7. Desmontagem, repair and meeting of the motor
      3.5.8. Turbocompressor
      +3.5.9. Lubrication system
      +3.5.10. System cooling
      3.5.11. Bad functioning standard of the motor
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

3.5.4.6. Check and adjust of turns of wasting time

GENERAL INFORMATION

Prevention

The check of the speed of the diesel engine needs a special tacômetro.

Speed that wastes time with the bomb of fuel of high pressure: DPC – 775±50 revolutions per minute.; DPRC – 875±25 revolutions per minute.

The screw of the limitador of the lever of a stop of the motor (1) and screw of the agreement of turns of wasting time (2)

The installation of the agreement Ford 23-016 (2) standard in the screw of the agreement of turns of wasting time (1)

ORDER OF REALIZATION

1. To heat the motor before being lit of the supporter of an electric heater.

2. To wait (in the motor to waste time) for the time being the supporter will not go out.

3. To put the motor out and to join a special tacômetro according to the enclosed education.

4. To begin the motor, at the same time all the electric consumers have to go out.

5. To unscrew the screw of limitador of lever of stop of motor before the emergence of a slit between the screw and the lever (to see the rice. The screw of the limitador of the lever of a stop of the motor (1) and screw of the agreement of turns of wasting time (2)).

6. To check the speed that wastes time. For the regulation of the speed of wasting time it is necessary to weaken a countersow and to make spinning the pin of agreement located on the lever of the bomb of fuel before obtaining necessary speed (to see the rice. The screw of the limitador of the lever of a stop of the motor (1) and screw of the agreement of turns of wasting time (2)).

7. The Dovintit the screw of emphasis of lever of stop of motor before contact with the lever and the beginning of increase in turns of wasting time.

8. To bring the motor to the very turns (not more than what during 5 seconds), to launch a pedal of a gas pedal and to measure the time from the reduction of turns to turns waste time. If the time exceeds 4 seconds it is necessary to adjust the time of the reduction of turns.

9. To withdraw a thread of gas pedal of a control they raise the bomb of fuel with lever of the high pressure.

10. In order that Ford 23-016 (2) establishes the agreement standard in an agreement that wastes time they screw the head. The absence of a standard to establish a plate of 3 mm of thickness instead of a standard (to see the rice. The installation of the agreement Ford 23-016 (2) standard in the screw of the agreement of turns of wasting time (1)).

11. To begin the motor and to measure turns of motor that will be in limits of 900±30 revolutions per minute. If necessary a value will establish adjusted daily pay of turns for the screw of the agreement of turns of wasting time of the motor.

12. To withdraw a standard, to join a thread of gas pedal, to check and if necessary turns it will adjust of wasting time of the motor.

13. If the speed reduces too many agudamente, then the motor tends to a stop. In this case it is necessary to unscrew the screw in 1/4 turns. If it reduces the speed when it exaggerated slowly, then it is necessary to crush the screw in 1/4 turns. In each one of these cases to check and if necessary turns it will adjust of wasting time of the motor.