Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
+3.1. Motor of OHC
+3.2. Motor of DOHC
+3.3. Motor of V6
+3.4. Systems of ignition and management of motor
-3.5. Diesel engines
3.5.1. Technical characteristic
3.5.2. The repair that does not demand the removal of the motor
3.5.3. Check and adjust of valves slits
-3.5.4. Fuel system
3.5.4.1. Mouths
3.5.4.2. Taken of incandescence
3.5.4.3. Check of a compression
3.5.4.4. Removal of air of system of fuel
3.5.4.5. Removal and installation of the bomb of fuel
3.5.4.6. Check and adjust of turns of wasting time
3.5.4.7. Increase thread in turns of wasting time
+3.5.5. Head of the cylinder block
3.5.6. Removal and installation of the motor
+3.5.7. Desmontagem, repair and meeting of the motor
3.5.8. Turbocompressor
+3.5.9. Lubrication system
+3.5.10. System cooling
3.5.11. Bad functioning standard of the motor
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment
|
Mouth
|
|
1 - channel of removal of fuel,
2 - adjust of lavador,
3 - spring,
4 - case of mouth,
5 - case of spray,
6 - it pricks,
7 - mouth |
For the definition of a defective mouth it is necessary to execute the next operations.
| ORDER OF REALIZATION |
| 1. In order that be convinced that the motor is useful and the level of a compression is identic in all the cylinders. |
| 2. To begin the motor and to heat it up to the work temperature. |
| 3. To weaken a nut of union of line of supply of fuel in the checked mouth. To notice if the motor becomes modified. To carry out the same control in the single accelerated to the course. |
| 4. In a useful mouth the obvious reduction of turns of the motor that results from his unequal work is going to be observed. If the checked mouth is defective, the modification of turns of the motor will be insignificant and it is going to go away if it went to present more advanced, foreign blow. |
|
Removal
| ORDER OF REALIZATION |
| 1. To withdraw the filter of air. |
| 2. To clear lines of supply of fuel of the high pressure, to unscrew nuts of hat in the fuel bomb and to protect them of the pollution. |
| 3. To unscrew lines of supply of fuel of mouths and to close them. |
| 4. A face key to unscrew mouths and to take away rings of fighter of copper and the lavadores isolate the heat of openings. |
| 5. The case of spray to insist on a vice with gentle sponges, to classify a mouth and use of the wooden instrument to compensate for all the details of a mouth. |
| 6. The mouth needle below a physical weight will slip densely in a spray nest. |
|
Installation
The lavador that isolates the heat
| ORDER OF REALIZATION |
| 1. To establish the new lavadores they isolate the heat directed by the curvature and soon new copper hunting touches a head of the cylinder block. |
| 2. The new installation is done in the sequence of the return to the removal. |
|
Mouths are allowed to use if after his desmontagem, cleaning and the subsequent meeting they restore the funcionalidade and they will hold all the checks. Check of tension of a spray of a mouth
One does in the device of the check of sprays.
Mouths check in tension
| ORDER OF REALIZATION |
| To establish a mouth in the device and to create the pressure of the opening of a mouth 2,0 MPas lower than the pressure. If inside 10 seconds in the temporary part of a spray around a needle there is no fuel in the form of the decrease that falls – the nest of a spray is held tight. In the lightly worn-out spray, his edge is moistened lightly, without the formation of a decrease. |
|
Agreement of initial pressure of injection
The initial pressure of the injection is regulated by the installation of the placing below one spring. I increase in the thickness of putting the pressure of increases of the beginning of the injection, the reduction – reduces. The modification of the thickness of the placing approximately modifies the pressure of the beginning of the injection to 0,01 mm in 1kg/cm2.
Fuel dispersal
The essential condition of the work of a mouth is the quality of the dispersal. The torch of the dispersal will be a uniform in the whole angry section of a cone of the dispersal, and the dispersal will be a nebula. The beginning and the end of the injection will be right. In new mouths the injection results from a sharp sound, For lack of mouths of work of this sound it is not a sign of bad functioning. |
|
