| 1. To insert in nests in the cylinder block they dry semiinsertions of radical loads. |
| 2. To the oil the surfaces of work of the semiinsertions and to establish in them an end of inclination. |
|
3. To establish together with the oiled semiinsertions of a covering of radical loads, the firearms in coverings of radical loads have to address towards the walk of axles (the arrow showed the marking of radical coverings). |
| 4. To hold tight pins of coverings of radical loads the corresponding moment. |
| 5. Through the group of probes to measure a play of axial side of an end of inclination. The probe is installed between a neck of an end of inclination and lavadores persistent. The size of a slit will be inside the values specified in the subsection 3.2.1. For the agreement of a slit it is possible to establish lavadores persistent of several thickness. |
| 6. To become an end of inclination to check if it sticks. If the end is turned very much only or traffic jams, it is necessary to carry out the desmontagem and the careful control. |
| 7. To cylinders of oil and pistons with the established one appropriately piston rings. |
|
8. To install ties the stick of piston with knot in cylinders, to hold tight piston touches the special adaptation. To straight arrows in pistons towards the walk of system of distribution of gas (to a caught motor). |
| 9. To establish sticks they are joined and sticks coverings, holding tight pins the corresponding moment. |
| 10. To check a play of axial side of sticks in necks conrod. |
| 11. To install in an opening in a rear part of an end of inclination the load of end of union. |
| 12. To take an old ring of rear fighter of an end of inclination of a covering. To install a covering in the cylinder block. The edges of work of a new hunting concern the fresh oil motor and to insert it in a covering through the corresponding tubular mandrel you embroider of work in the interior. |
| 13. To establish an advanced covering of the cylinder block. |
| 14. To establish a maslootrazhatel and a tube maslozaborny with the new placing. |
| 15. To establish the new placing in flutes of a case of oil. |
| 16. To apply the selante in the inter-connected sieges to a covering of a ring of fighter. |
| 17. To establish a case of oil. |
| 18. To establish a pendulum in an inclination end, when the fastenings of the pendulum are holding tight pins (to the oil a woodcarving) the corresponding moment. |
| 19. Through the adaptation to center a plate of pressure in a pendulum and to establish the main part of the union. |
| 20. To install the sensor of the provision of an end of inclination and the sensor of the pressure of oil. |
| 21. To install at the place the bomb of oil and to hold tight the fixation it fires on the corresponding moment. |
| 22. To establish a filter of oil and the water bomb. |
| 23. To install the new placing in the cylinder block. |
| 24. To become an end of inclination so that the pistons were installed in the middle of the course. |
| 25. To install a head of the cylinder block in the cylinder block. |
| 26. To polish with a fine layer of oil of motor a woodcarving of pins of the fixation of a head of the cylinder block, to establish them at the place and to hold tight the necessary moment in certain sequence (3.2.1 to see the subsection). |
| 27. To polish with a fine layer of oil of motor of a support of axles in a head and to install in place axles. |
| 28. To polish with a fine layer of oil of motor of a covering of loads of axles and to establish them at the place according to the marking. The coverings of loads of the axle of the managing director of valves of entry have the marking of R1-R5, and the coverings of loads of the axle of the managing director of final valves have the marking of L1-L5. Numeration of coverings of the walk of mechanism of distribution of gas. |
| 29. To install the oil pipeline of the provision of oil to axles cames. |
| 30. Gradually and constantly there insist nuts of the fixation of coverings of the fixation of axles on certain sequence. To the hand to hold tight nuts of fixation, turning them it is consecutive in 180 ° before the contact of a covering with a head of the cylinder block. Pressure sequence: L1 and R1, L5 and R5, L3 and R3. Then to put to the hand other armbands of the fixation of coverings. |
| 31. To hold tight nuts of the fixation of coverings the necessary moment, turning them in the same corner in the next sequence: L1 and R1, L5 and R5, L3 and R3, L2 and L4, R2 and R4. |
32. To check that the inclination end is in the situation that corresponds to the installation of the piston of the cylinder 1 in the superior dead point in a compression step, at the same time the groove shponochny has to address down.
Prevention
 In a chain of the mechanism that distributes the gas there are elements of copper that are in use for the correct agreement of the mechanism of the distribution of gas during the installation of a chain.
|
| 33. To lower a chain from above in a covering, at the same time the only connection of copper of a chain will be down. |
| 34. To insert a spline in a groove of an end of inclination. |
| 35. To establish a chain in a (big) internal asterisk, having combined at the same time a connection of copper of a chain with an etiquette in an asterisk. |
| 36. To establish an asterisk in an inclination end, having combined a groove in an asterisk with a spline, at the same time the etiquette in an asterisk will be strictly down. |
| 37. To insert from above at the place the lowest uspokoitel of a chain and it is screwed pins which woodcarving is covered of the ways interference to unscrew of pins. |
| 38. To establish a hydraulic empurrador of a natyazhitel of a chain. |
| 39. To install the lever of a natyazhitel of a chain, an axle of the lever of a natyazhitel and to fix it for a lock lavador. |
| 40. To check and if necessary axles it will install in an initial position. The axles will be in the situation that corresponds to the installation of the piston of the cylinder 1 in the superior dead point in a compression step, and adjusting edges of asterisks will be in a line with the superior edge of a head of the cylinder block and will address on the outside. |
| 41. To establish a chain in an asterisk of the final axle, having combined an etiquette in an asterisk with the way of the siege of a chain between connections of copper of a chain. |
| 42. To install an asterisk in the axle. At the same time the etiquette in an asterisk will be in a line with the superior edge of a head of the cylinder block and to address on the outside. To screw a pin of the fixation of an asterisk. |
| 43. To establish a chain in an asterisk of the axle of entry, having combined an etiquette in an asterisk with the way of the siege of a chain between connections of copper of a chain. |
| 44. To install an asterisk in the axle. At the same time the etiquette in an asterisk will be in a line with the superior edge of a head of the cylinder block and to address on the outside. |
| 45. To install a distributor of ignition they direct the wheel of gear in the right axle. |
| 46. To establish the top uspokoitel of a chain of the mechanism that distributes the gas. |
| 47. To become an end of inclination in several business volumes of the direction of the rotation of work of the motor. |
| 48. To check the provision of a diver of a hydraulic empurrador. |
| 49. To become an end of inclination in two business volumes of the direction of the rotation of work of the motor and to check etiquettes in asterisks of axles that will be in a line with the superior edge of a head of the cylinder block and it will address on the outside. |
| 50. To become an end of inclination in a business volume of the direction of the rotation of work of the motor and to check etiquettes in asterisks of axles that will be in a line with the superior edge of a head of the cylinder block and one will direct one to other. |
| 51. To establish a chain of the walk of the bomb of oil in an asterisk of an end of inclination, soon to install an asterisk of driving together with a chain in the oil bomb. |
| 52. To establish a natyazhitel of a chain of the bomb of oil. |
| 53. To check a condition of a hunting they touch the superior covering of the distributive mechanism. If necessary an old fighter ring will take and, using a tubular mandrel, to establish a new ring for work edges to the motor. |
| 54. To establish the superior covering of the distributive mechanism with the new placing. |
| 55. To establish a covering of a head of the cylinder block. |
| 56. To check a condition of a hunting they touch the lowest covering of the distributive mechanism. If necessary an old fighter ring will take and, using a tubular mandrel, to establish a new ring for work edges to the motor. |
| 57. To establish the lowest covering of the distributive mechanism with the new placing, without holding tight pins of fixation. |
| 58. To establish a pulley of an auxiliary belt in an inclination end and to fix it for an old pin, at the same time aligning the lowest covering of the distributive mechanism and to hold tight finally pins of the fixation of a covering. |
| 59. To unscrew an old pin of a pulley and to support in the new, having held tight it the necessary moment. |
| 60. To install the mechanism of a tension of an auxiliary belt, at the same time the edge in a rear part of the mechanism of a tension will enter in the corresponding opening in the cylinder block of the motor. |
| 61. To establish taken of spark, the distributor of wires of high voltage and ignition. |
| 62. To install the creator, to put a belt of driving and to adjust his tension. |
|
63. To fill out the oil of motor in the motor. |
