Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
+3.1. Motor of OHC
-3.2. Motor of DOHC
3.2.1. Technical characteristic
+3.2.2. The repair that does not demand the removal of the motor
+3.2.3. Removal and installation of the motor without transmission
3.2.4. System of ventilation of a case
-3.2.5. Lubrication system
3.2.5.1. Removal and installation of a case of oil
3.2.5.2. Removal and installation of the bomb of oil
3.2.5.3. Desmontagem of the bomb of oil
+3.3. Motor of V6
+3.4. Systems of ignition and management of motor
+3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment
|
Elements of system of lubrication
1 - sensor of pressure of oil,
2 - oil filter,
3 - level of oil that measures tube of instrument,
4 - I score of measuring of oil level, |
5 - placing of the trundle bed of oil,
6 - oil trundle bed,
7 - cork of masloslivny |
Removal
| ORDER OF REALIZATION |
| 1. To withdraw the transmission. |
| 2. To withdraw the union. |
| 3. To remove a pendulum and a protective policeman of the motor. |
| 4. To fuse the oil of motor of his motor. |
| 5. To check what the steering-wheel establishes in the provision of the movement straightly ahead and painting or a marker to observe the provision of the lowest collar of an intermediary end and wheel of gear of directing the transfer, soon desconectar an intermediary end of directing the transfer. |
| 6. Care that has, the mechanism that lifts the load to lift the motor, and soon in order that bearers of the motor unscrew. |
| 7. Desconectar tubes of brake of a ray of an advanced support of the triangular form of interruption. |
| 8. To support a ray through the corresponding elevator and a wide plank. |
| 9. To unscrew pins of the fixation of a ray to the bottom of the car. To tilt a ray so that the access to a case of oil was launched. |
| 10. To unscrew pins and nuts of the fixation of a case of oil and to take it of bass of the motor. |
|
Installation
Places of putting the selante in the inter-connected surfaces of a case of oil and the cylinder block
|
|
2 - places of putting the selante |
| ORDER OF REALIZATION |
| 1. To compensate carefully for the inter-connected surfaces of the cylinder block and a case of oil. |
| 2. To establish the new placing in flutes of a case of oil. |
| 3. To apply the selante in the inter-connected sieges to a covering of a ring of fighter. |
| 4. To apply the interference of structure to unscrew in a woodcarving of pins and nuts, to establish a case of oil and to put pins and the armbands without holding tight them is final. |
|
5. At the level they are in front of surfaces of a case of oil and the cylinder block and to hold tight finally pins and nuts. If between face surfaces there is a step, it is necessary to measure it and depending on the size of a step to establish the placing of the recommended thickness. |
| 6. The new operations are done in the sequence, the return to the removal. |
|
|
Step size
|
Thickness
|
Color of the established placing
|
|
0 - 0,25 mm
|
not to establish the placing
|
|
0,25 - 0,29 mm
|
0,15 mm
|
silver
|
|
0,30 - 0,44 mm
|
0,30 mm
|
blue
|
|
0,45 - 0,59 mm
|
0,45 mm
|
I redden
|
|
0,60 - 0,75 mm
|
0,60 mm
|
black
|
|
|
