FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+ 4. System cooling
- 5. Fuel system
   5.1. Technical characteristic
   5.2. Fuel
   5.3. Gasoline without lead of V6, 2,4 motors and 2,9 dm3
   +5.4. System of air provision
   +5.5. Carburator of PIERBURG
   +5.6. WEBER 2V carburator
   +5.7. WEBER 2V carburator of TLD
   -5.8. System of injection of fuel
      5.8.1. Turns agreement of wasting time and quality of mixture
      5.8.2. Removal and installation of the sensor of provision of a valve of butterfly
      5.8.3. Removal and installation of the valve of management of turns waste time
      5.8.4. Removal and installation of measuring instruments of a draft
      5.8.5. Removal and installation of mouths of fuel
      5.8.6. Removal and installation of the sensor of temperature of the road of fuel
      5.8.7. Removal and installation of the regulator of pressure of fuel
      5.8.8. Removal and installation of the case of a valve of butterfly in the motor DOHC
      5.8.9. Removal and installation of the sensor of oxygen (HEGO)
      5.8.10. Removal and installation from a coal adsorber
      5.8.11. Removal and installation of the valve eletromagnética of a coal adsorber
   5.9. Removal and installation of a collector of entry
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

5.8.3. Removal and installation of the valve of management of turns waste time

GENERAL INFORMATION

Valve of management of turns of wasting time of the motor DOHC

The valve of the management of turns of wasting time is specified by an arrow.

ORDER OF REALIZATION

OHC and motors V6
1. To withdraw a weight they connect of the accumulator.
	2. To withdraw the capture (it is specified by an arrow) of the valve of the management, without having bent the clip of property.
	3. To unscrew two nuts of fixing (ONS) (or a pin in the motor V6) and to take the valve (it is specified by an arrow).
4. If necessary two screws it will unscrew and withdraw the roll of the valve.
5. To install at the place the valve, using the new placing, to hold tight nuts or pins.
6. To join the capture and a wire of the mass of the accumulator.
7. To begin the motor and to check the stability of wasting time.
8. To heat the motor up to the work temperature, electric consumers to include everything and to check that the turns of wasting time remained that you were.
Motor of DOHC
9. To withdraw a weight they connect of the accumulator.
10. To weaken a collar and desconectar a hose of airintaking of a regulator.
11. To unscrew a nut of the fixation and desconectar a tube airintaking of a support of triangular form in the advanced list of a driving compartment.
12. To withdraw the capture of the valve of the management, without having bent the clip of property.
13. Desconectar clips of a covering of the filter of air, to catch the telephone of airintaking, the camera of the excessive pressure and a covering of the filter of air like a meeting, having desconectado a hose of the ventilation of a case of a tube airintaking.
14. To unscrew two pins of the fixation and to take the valve of a tube airintaking.
15. The installation is done in the sequence, the return to the removal.
16. To begin the motor and to check the stability of wasting time.
17. To heat the motor up to the work temperature, electric consumers to include everything and to check that the turns of wasting time remained that you were.