FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car


Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+ 4. System cooling
- 5. Fuel system
   5.1. Technical characteristic
   5.2. Fuel
   5.3. Gasoline without lead of V6, 2,4 motors and 2,9 dm3
   +5.4. System of air provision
   +5.5. Carburator of PIERBURG
   +5.6. WEBER 2V carburator
   +5.7. WEBER 2V carburator of TLD
   +5.8. System of injection of fuel
   5.9. Removal and installation of a collector of entry
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment


bfe6b27a


5.9. Removal and installation of a collector of entry
GENERAL INFORMATION

Taken of a braid of wires of system of injection of fuel

The capture of a braid of wires is specified by an arrow.

Places of putting the selante in the inter-connected surfaces

The places of putting the selante are specified by firearms.

Removal of a collector of the road of fuel and doors of injection

The door of the injection is specified by an arrow.

MOTORS OF OHC

ORDER OF REALIZATION
1. To withdraw a weight they connect of the accumulator.
2. To fuse the liquid that cools.
3. Desconectar electronic valves of a collector. The quantity of tubes depends on the model and the equipment.
4. To withdraw taken of braids of mouths of fuel in the end of the oil pipeline, beside a splitting.
5. Desconectar a wire of the sensor of a bulb of control of the pressure of oil under a collector.
6. To weaken collars and to withdraw the road, the instrument of measuring of a draft and the oil pipeline of a collector.
7. To discover the distributor and desconectar wires of high voltage.
8. To unscrew two nuts and to withdraw the support that goes of a collector to the right side of a head of cylinders.
9. To unscrew four pins and to withdraw a support that joins the collector's base to the left side of the block.
10. To unscrew a support of the triangular form of a thread of a gas pedal and to move it to the part.
11. Desconectar a tube of the provision of the fuel of an arm of fuel and a repayable tube of the regulator of pressure of fuel.
12. Desconectar a hose of system of cooling of a collector.
13. To unscrew six nuts and pins of the fixation of a collector (it is specified by firearms) and to withdraw it. The basic wire can be joined to one of hair clips of hair by an additional nut.
14. To withdraw carefully of a head of the cylinder block of the collector together with details if they adhere. If the distributor prevents the removal, to unscrew a hair clip of advanced hair of a collector or to remove the distributor.
15. To withdraw the placing of a head of the cylinder block.
16. The installation is done in the sequence, the return to the removal. To apply a layer of selante in the inter-connected surfaces.

MOTORS OF DOHC

ORDER OF REALIZATION
1. To withdraw a weight they connect of the accumulator.
2. To fuse the liquid that cools.
3. Desconectar cools hoses of the case of the thermostat and a collector of entry.
4. Desconectar a branch tube of airintaking on an advanced part of a collector of entry.
5. Desconectar hoses of the ventilation of a case and vacuum waters with hose of a collector of entry.
6. Desconectar a gas pedal thread.
7. To withdraw wires of high voltage of captures of spark and to move them to the part.
8. Desconectar wires of the switch of the ventilator of an electric heater, the sensor of the temperature of cooling the liquid of the motor and the sensor of the measurement of the temperature.
9. To withdraw the capture of the sensor of the provision of a valve of butterfly.
10. To withdraw mouths of fuel.
11. To unscrew 10 pins and 2 nuts of the fixation of a collector to a head of the cylinder block and to remove exactly a collector of entry. To withdraw the placing.
12. 2 takes placing of plastic candle of a nest in a head of cylinders.
13. The installation is done in the sequence, the return to the removal. To fill out the liquid in the cooling system and to check turns of wasting time and maintenance with.

MOTORS OF V6

Final connection of the system of cooling in the oil pipeline of entry of the motor V6


Order of pressure of driving pins of fixation of a collector of entry of V6


ORDER OF REALIZATION
1. To withdraw a weight they connect of the accumulator.
2. To fuse the liquid that cools.
3. To discover the lever of regulator.
4. To weaken collars and the instrument moves to the part the road of measuring of current of air collector.
5. To withdraw a hose of the ventilation of a case.
6. To withdraw the best hose of an electric heater and a hose of a heater of a passage of leak in an advanced part of the oil pipeline.
7. Desconectar been overcome with the valve of turns of wasting time, the sensor of the measurement of the temperature, the sensor of the measurement of the temperature of cooling the liquid and the sensor of the provision of a valve of butterfly. Desconectar a braid of wires of mouths of fuel.
8. Desconectar a thread of gas pedal of the lever. In models with the automatic exchange also for desconectar I lower a thread of the kick or the capture.
9. Desconectar tubes of offer and return of the fuel.
10. To remove wires of high voltage and the distributor of the ignition.
11. To unscrew eight pins and to withdraw the camera of the excessive pressure.
12. To unscrew seven pins and to discover a head of the cylinder block.
13. For desconectar of an entry collector they go round a hose of the water bomb.
14. To unscrew eight pins and to remove a collector of entry.
15. It to remove a collector when of it entered together with the regulator of pressure, an arm of fuel and a covering of the case of a regulator.
16. The installation is done in the sequence, the return to the removal. To apply a layer of selante in the inter-connected surfaces.