FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   +3.3. Motor of V6
   +3.4. Systems of ignition and management of motor
   -3.5. Diesel engines
      3.5.1. Technical characteristic
      3.5.2. The repair that does not demand the removal of the motor
      3.5.3. Check and adjust of valves slits
      +3.5.4. Fuel system
      +3.5.5. Head of the cylinder block
      3.5.6. Removal and installation of the motor
      -3.5.7. Desmontagem, repair and meeting of the motor
         3.5.7.1. Desmontagem
         -3.5.7.2. Meeting of the motor
            3.5.7.2.1. Installation of the back radical load
            3.5.7.2.2. Installation of selantes from side
            3.5.7.2.3. Meeting of stick of piston of knot
            3.5.7.2.4. Selection of pistons of diameter of the cylinder
            3.5.7.2.5. Meeting of the walk of system of distribution of gas
            3.5.7.2.6. New actions of meeting of the motor
      3.5.8. Turbocompressor
      +3.5.9. Lubrication system
      +3.5.10. System cooling
      3.5.11. Bad functioning standard of the motor
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

3.5.7.2.4. Selection of pistons of diameter of the cylinder

GENERAL INFORMATION

Knot of the cylinder block

1 - cylinder block,
2 - oil trundle bed,
3 - pin of fixation of the trundle bed of oil,
4 - drain the cork of oil,

5 - coverings of technological openings of the cylinder block,
6 - I set pins,
7 - hat of a technological opening

Cylinders designations in the cylinder block of the motor and pistons in his bottom

The diameters of pistons and cylinders are divided in groups that are nominated by the letters that are beaten in the cylinder block of the motor and the day of the piston.

The cylinder and the piston that interacts with him will belong to a group of the choice.

Prevention

The new motors cylinder blocks have cylinders with a diameter only of the group "A" and "B".

Check of a vystupaniye of the piston is left the best airplane of the cylinder block

ORDER OF REALIZATION

1. To oil the surfaces of pistons and the internal surfaces of cylinders.

2. Through the device of the compression of rings to insert it ties the stick of piston with knot in the corresponding cylinders.

Prevention

To become more deep in the bottom of the piston has to address towards the fuel bomb.

3. To hold tight pistons deeply in of cylinders.

4. To establish sticks they are joined and sticks coverings, to hold tight nuts of pins of the fixation of coverings of sticks the moment of 60 nanômetros.

5. To measure the moment of resistance in the moment of the rotation of an end of inclination through a dynamometer key.

6. The oil empurradores and to insert them according to the designations in guides of the cylinder block of the motor.

7. To install in the cylinder block an axle and an intermediary plate together with the new placing. To install the walk of the system of the distribution of gas (3.5.7.2.5 to see the subsection) and a covering of a chain of driving of the system of the distribution of gas together with the new placing.

8. To polish pins of a covering of a chain of driving of the system of the distribution of gas with the briefcase of Frenetanch that pressuriza and to hold tight his moment 10 nanômetros.

9. To annex to the cylinder block the bomb of oil so that the conical opening in a bomb accommodation was installed in front of an opening with a woodcarving.

10. To delay the moment 22,5 nanômetros for pin (with the conical ending) the fastenings of the bomb of oil.

11. To establish a lavador of copper and to hold tight a nut with the moment of 30 nanômetros deadened by an opening.

12. To establish a lavador of original agreement and to hold tight carefully a cork with a woodcarving.

13. To install the trundle bed of oil. To delay the cork of 3 nanômetros for moment drain with the new placing.