Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
+3.1. Motor of OHC
+3.2. Motor of DOHC
+3.3. Motor of V6
-3.4. Systems of ignition and management of motor
3.4.1. Technical characteristic
-3.4.2. Systems of ignition and management of motor
3.4.2.1. System of ignition of ESC II
3.4.2.2. System of ignition of EEC IV
3.4.2.3. Ignition distributor
3.4.2.4. Check of an angle of installation of an advancement of ignition
3.4.2.5. The block of ignition (models with system of injection of fuel)
3.4.2.6. Ignition roll
3.4.2.7. A fuel capture in motors with the carburator
3.4.2.8. Unity of control of the motor
3.4.2.9. Motor of step of the carburator
3.4.2.10. The device of heating of a collector of entry of motors with the carburator
3.4.2.11. Alternation of a system of control of the motor
3.4.2.12. Installation of a corner of an advancement of ignition and turns of wasting time
3.4.2.13. Meter of REVOLUTIONS PER MINUTE and provisions of an end of inclination
3.4.2.14. Air temperature sensor
3.4.2.15. Sensor of temperature of fuel
3.4.2.16. Sensor of speed of the car
3.4.2.17. The sensor of absolute pressure in a collector (MAP)
+3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment
|
Distributor of ignition of motor of OHC
|
|
1 - covering,
2 - distributor's rotor,
3 - ignition distributor,
4 - ring fighter,
5 - taken |
Distributor of ignition of motor of DOHC
|
|
1 - hints of wires of high voltage,
2 - screw of fixation of a covering,
3 - covering,
4 - distributor's rotor,
5 - I set pins,
6 - distributor's walk |
Wires of high voltage and captures of spark of the motor DOHC
|
|
1 - the capture sparkles,
2 - it works as a prompter,
3 - wires of high voltage,
4 - bearers of wires of high voltage |
The provision of a rotor of the distributor before and after removal
ALL THE MOTORS, EXCEPT V6 2,4 and 2,9 dm3
Prevention
 The distributor of the ignition must not retire without the serious reason as the exactness of the installation of a corner only there can be restored an advancement of ignition got in the production.
| ORDER OF REALIZATION |
| 1. To withdraw a negative wire of the accumulator. |
| 2. To discover the distributor. |
3. The use of a key, for a pin of a pulley of an end of inclination, to turn the motor before the installation of the piston of 1 cylinder in a point of ignition that is when:
– the etiquettes adjust that they are in the provision of the combination;
– the rotor of the distributor goes with the contact of a wire of high voltage of 1 cylinder. |
| 4. When the cylinder is in the provision of the ignition, the rotor has to go with a groove in case of distributor. |
| 5. To pull out a clip of blockade in the capture of multiproduction of the distributor and to call - of the capture. |
| 6. To put etiquettes of combination in the distributor and the motor, soon to unscrew a pin of the fixation of the distributor and a level apertador. In motors V6 because of the limited access it is necessary to use a special key. If the support of the triangular form of support is established, to unscrew it. |
|
7. To remove the distributor of ignition, having noticed the new provision of a rotor of the distributor. Like spare pieces to a distributor (2) over the rotor of the distributor and a ring of fighter of the section round (1) they hand. |
| 8. During the installation of the distributor of the ignition to establish a rotor in the situation in which it was after the removal that it is he has to turn in 20 ° in the direction of the movement of the pointers of the clock of the moment of the ignition of 1 cylinder. |
|
9. To install the distributor of ignition in the motor, at the same time the rotor of the distributor will turn in reverse sense to the movement of the pointers of the clock and to be established in the situation in which it was before the removal, otherwise to repeat the installation. The correct installation of the distributor of the ignition is determined by the combination of an etiquette (1) in a rotor with an edge (2) in case of distributor. For the right combination of an etiquette and an edge it is necessary to turn the distributor's case in one or another party. |
| 10. To establish a level apertador and to fix the distributor for a pin. |
| 11. The new installation is done in the sequence, the return to the removal. |
|
Dm3 V6 2,4 I MOTORS 2,9
Prevention
The distributor of the ignition must not retire without the serious reason as the exactness of the installation of a corner an advancement of the ignition can be got only with the use of the special equipment.
The provision of a rotor before installation in the motor of V6 2,4 and 2,9 dm3
|
|
With – an etiquette in the case |
| ORDER OF REALIZATION |
| 1. To withdraw a negative wire of the accumulator. |
| 2. To withdraw wires of high voltage of captures of spark. |
| 3. To discover the distributor of the ignition and to move it to the part together with wires. |
|
4. To turn the motor of a pin of the fixation of a quencher of fluctuations tortional in a point of the installation of the piston of 1 cylinder in the moment of the ignition (12 ° to the superior dead point), when 12 combined an etiquette in a pulley of an end of inclination (1) with the division ° in a scale of the installation of the moment of the ignition (2). |
| 5. The absence of an etiquette in a pulley of an end of inclination to put etiquettes of combination besides precisely for establishing a distributor's rotor. |
| 6. To observe the provision of a plate of the installation of the distributor of the ignition about the cylinder block. |
| 7. Desconectar the capture of the distributor of ignition. |
|
8. To unscrew a pin (of 1) of the fixation and to remove the distributor of the ignition (2). |
| 9. To install the distributor of ignition so that the installation etiquettes combined. |
| 10. After the installation of the distributor, making spinning the case of the distributor to combine the contact of a rotor with an etiquette with in the case (to see the rice. The provision of a rotor before the installation in the motor of V6 2,4 and 2,9 dm3) and to protect the distributor in this provision for a pin. |
| 11. The new installation is done in the sequence, the return to the removal. |
| 12. To heat the motor and to check the installation of a corner of an advancement of the ignition. |
|
|
|
