FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+ 6. Union
- 7. Transmissions
   +7.1. Mechanical transmission of five speeds of type of N
   +7.2. Mechanical MT 75 transmission
   -7.3. Transmission A4LD automatic
      7.3.1. Technical characteristic
      -7.3.2. Service and repair
         7.3.2.1. Work description
         7.3.2.2. Check of level of oil in the transmission
         7.3.2.3. Check and washing of the hydrokinetic transmission
         7.3.2.4. Check of pressure of oil in operational time of the transmission
         7.3.2.5. Test of an overload of the hydrokinetic transfer of motor
         7.3.2.6. Agreement of a stares of a brake of advanced planetary transfer
         7.3.2.7. Removal and installation of the regulator of vacuum
         7.3.2.8. Hydraulic auxiliary rocket of reverse planetary gear
         7.3.2.9. Centrifugal regulator of pressure of oil
         7.3.2.10. Substitution of a ring of rear fighter
         7.3.2.11. Removal and installation of the mechanism of the choice of transfers
         7.3.2.12. Removal and installation of sketch of the choice of transfers
         -7.3.2.13. Agreement of a thread of the mechanism of Kick down
            7.3.2.13.1. Cars with the valve eletromagnética
         7.3.2.14. Removal and installation of the transmission
         7.3.2.15. Bad functioning of the automatic exchange
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

7.3.2.13. Agreement of a thread of the mechanism of Kick down

GENERAL INFORMATION

The sizes of standard of agreement of a thread of the mechanism of kick down

Agreement of a thread of the mechanism of kick is lowered by me in the 1st execution version

E - a nut of agreement of a tension of a thread of the mechanism of kick is lowered by me,

In – a countersow,

With – a nut of agreement of a tension of a thread of a pedal of a gas pedal,

D - covering does away,

X = 8 mm – the control size

ORDER OF REALIZATION

1. To weaken a nut (A) of the agreement of a tension of a thread of the mechanism of kick I lower and his countersow (in).

2. To move a nut and a countersow up to the end of a woodcarving.

3. To hold tight against the stop a pedal of a gas pedal and to register it in this situation.

4. There become a nut (C) the agreements of the tension of a thread of a pedal of a gas pedal before X to obtain the size = 10 mm. By the check of the size (X) the use of a standard as the rice is recommended. The sizes of standard of agreement of a thread of the mechanism of kick down.

5. In the course of the turn of a nut (C) (to see the rice. The agreement of a thread of the mechanism of kick is lowered by me in the 1st version of the execution) the spring, operty in him, and they cannot turn the capture as (X) would cause the modification of the size during the movement of the car.

6. After the agreement to take a standard.

7. Between elements for which the size (X) makes up his mind putting the second party of a standard according to the rice. The sizes of standard of the agreement of a thread of the mechanism of kick are lowered by me 8 mm (width) and to launch a pedal of gas pedal. The standard will remain held tight by these elements.

8. A thread pulls a hand (D) of covering of the mechanism of kick I lower in the direction shown by an arrow in the rice. The agreement of a thread of the mechanism of kick is lowered by me in the 1st version of the execution to remove a play of side of a thread and to maintain a covering in this situation.

9. To put the armband of agreement (A) in his emphasis on a covering plate, and soon to hold tight his countersow (in).