FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car


Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+ 6. Union
- 7. Transmissions
   +7.1. Mechanical transmission of five speeds of type of N
   +7.2. Mechanical MT 75 transmission
   -7.3. Transmission A4LD automatic
      7.3.1. Technical characteristic
      -7.3.2. Service and repair
         7.3.2.1. Work description
         7.3.2.2. Check of level of oil in the transmission
         7.3.2.3. Check and washing of the hydrokinetic transmission
         7.3.2.4. Check of pressure of oil in operational time of the transmission
         7.3.2.5. Test of an overload of the hydrokinetic transfer of motor
         7.3.2.6. Agreement of a stares of a brake of advanced planetary transfer
         7.3.2.7. Removal and installation of the regulator of vacuum
         7.3.2.8. Hydraulic auxiliary rocket of reverse planetary gear
         7.3.2.9. Centrifugal regulator of pressure of oil
         7.3.2.10. Substitution of a ring of rear fighter
         7.3.2.11. Removal and installation of the mechanism of the choice of transfers
         7.3.2.12. Removal and installation of sketch of the choice of transfers
         +7.3.2.13. Agreement of a thread of the mechanism of Kick down
         7.3.2.14. Removal and installation of the transmission
         7.3.2.15. Bad functioning of the automatic exchange
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment


bfe6b27a


7.3.2.14. Removal and installation of the transmission
GENERAL INFORMATION

Amount of control of deepening of hydrokinetic transfer

E = 10 mm

Removal

ORDER OF REALIZATION
1. To install the car on the observation channel or in the elevator and desconectar they connect a weight of the accumulator.
2. Of a driving compartment to unscrew four superior pins of the fixation of the automatic exchange to the cylinder block of the motor.
3. For desconectar a reception they exhaust the tube of a collector.
4. Desconectar elements of rubber of a support of the triangular form of interruption of supports of the triangular form of the fixation of a rear part of the final system and to lift the system to a body through a wire.
5. Desconectar the driving axle of the transmission and there deadens an opening in his rear part of a case a cork of the artificial material so that there was no oil effluence.
6. To withdraw the stabilizer.
7. Desconectar electric wires of an author and to remove an author.
8. In models with the motor V6 to discover the distributor.
9. To catch the maslozalivny they phone and an opening closes a cork in a case of transmission.
10. There unscrew 4 pins of the fixation of a ray of the transmission to beams schoolmistresses of side and 1 pin of the fixation of the transmission.
11. Desconectar oil pipelines of oil of an electric heater of oil and to deaden his openings.
12. Two withdraws protection and knot of sketches of the lever of the dislocation of gear.
13. Desconectar a thread of the lever of a reduction of transfers and of the bearer of a thread.
14. Desconectar a vinculação of electric wires of the alternation of the safe launch of the motor.
15. For desconectar the speedometer they do the thread located in an exsensitive case.
16. Desconectar the oil pipeline of vacuum of the regulator of vacuum of the automatic exchange and to withdraw an arm.
17. To unscrew pins of the fixation of a disc of the walk of the hydrokinetic transfer through an opening of the retired author (the pin of the fixation is specified by an arrow).
18. To unscrew pins of the fixation of a crossbeam of the transmission and to lower carefully the transmission.
19. To take the transmission, maintaining the hydrokinetic transfer in his case.

Installation

ORDER OF REALIZATION
1. In case of the necessity of taking the rings that direct a flange of the hydrokinetic transfer and of holding tight them in the cylinder block of the motor.
2. To establish the hydrokinetic transfer in a case if it took of him. The cork of the unloading of oil of the hydrokinetic transfer will be in an axle of an opening of a disc of driving. After the installation of the hydrokinetic transfer at the place appropriated in a case it is necessary to check if it does the size of control (A) between a flange of the hydrokinetic transfer and a surface frontlet of a 10 mm case.
3. Pins pinch of flange after the check if the freely great hydrokinetic transfer in a case.
4. To the oil of automatic exchanges and to insert the oil of oil pipeline that is filled in the short oil pipeline in a case.
5. To annex a crossbeam of support of the triangular form of interruption to the transmission.
6. To lift the transmission and to fix a crossbeam of support of the triangular form of interruption to a body.
7. To insert and to hold tight the corresponding pins of moment of the fixation of a disc of driving to the hydrokinetic transfer.
8. Electric wires adhere to an author and the alternation of the safe launch of the motor, and also the vacuum oil pipeline to the regulator of vacuum of the transmission.
9. In order that oil pipelines adhere to an oil electric heater and a speedometer they direct the thread.
10. A thread adheres to a bearer on the transmission, and also to the lever of a reduction of transfers.
11. To install the lever of the dislocation of gear and a lever of control in the transmission in the situation "D" and to fix elements of the extern mechanism of the management of the automatic exchange (without his walk).
12. Of an opening in a rear part of a case of the transmission to take a cork of the artificial material and to install the driving axle.
13. To install the stabilizer of an advanced support of the triangular form of interruption.
14. To annex the supports of triangular form maintaining oil pipelines of vacuum and oil pipelines of oil.
15. To annex a support of the triangular form of interruption of a rear part of the final system to a body.
16. To check the level of oil and if necessary the amount of oil will fill in the transmission (7.3.2.2 looks at the corresponding description in the subsection).
17. To check the tension of connections and oil pipelines.