FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   +3.3. Motor of V6
   +3.4. Systems of ignition and management of motor
   -3.5. Diesel engines
      3.5.1. Technical characteristic
      3.5.2. The repair that does not demand the removal of the motor
      3.5.3. Check and adjust of valves slits
      +3.5.4. Fuel system
      -3.5.5. Head of the cylinder block
         3.5.5.1. Removal of a head of the cylinder block
         3.5.5.2. Installation of a head of the cylinder block
         3.5.5.3. Check and repair of a head of the cylinder block
      3.5.6. Removal and installation of the motor
      +3.5.7. Desmontagem, repair and meeting of the motor
      3.5.8. Turbocompressor
      +3.5.9. Lubrication system
      +3.5.10. System cooling
      3.5.11. Bad functioning standard of the motor
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

3.5.5.3. Check and repair of a head of the cylinder block

GENERAL INFORMATION

These proceedings are executed after the removal of a head of the cylinder block.

Amount (A) of deepening of a guide of the valve

ORDER OF REALIZATION

1. To withdraw the bomb of cooling liquid, a final collector, cameras of combustion of vortex and a thermoswitch of a bulb of control of overheating of the motor.
	2. Through the device of the spring compression of valves to withdraw fine cookies of the fixation of the superior persistent spring plates and to withdraw springs of valves.
3. To take the valve and to indicate in which cylinder they worked.
4. The dish does in gasoline or fuel spring diesel of valves, paying attention to the damnification from his cloth for sheets.
5. Through a brush of gentle wire carefully to compensate for final channels in a head of the cylinder block, the extern surfaces of the valves of direction and the valve.
Prevention It is impossible to use devices that can scratch the compensated details.
6. To a clear one and all the details take carefully the compressed air.
7. Through a sovereign to check planeness of the lowest airplane of a head of the cylinder block: lengthways, across and in diagonal. In the course of the check not the opirat a sovereign in cameras of combustion (it can act lightly of a head of the cylinder block).
8. In case of the necessity of substituting guides of valves and of checking the provision of guides after his installation.
9. After the installation in a head of the cylinder block for mandrilar the internal diameter of the valves of direction to the corresponding sizes.
10. To grind in the valve through the briefcase of fine granulation to grind in.
11. The dish does carefully a head of the cylinder block and the valve of the removal of particles of briefcase.
12. To check a condition of surfaces of work of nests of valves.
13. To check a prileganiye of valves to his nests, turning the valve in 1/8 he turns in the moment from his easy pressing to a nest.
	14. To measure the deepening valve of somewhat they lower the airplane of a head of the cylinder block.
15. To check a condition of the taken cameras of combustion.
	16. After the installation of cameras of combustion in a head of the cylinder block through indicative of the hour they type to check his vystupaniye (0-0,03 mm) of the lowest airplane of a head of the cylinder block.
17. To join a head of the cylinder block, having executed operations in the return sequence regarding the described one in top.