FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

3.1.2.2.1. Removal and installation of a belt of gear

GENERAL INFORMATION

Removal of the device of tension of a belt of gear through a few 21.012-key

1 - tension device,

2 - spring,

3 - pin agreement,

4 - roll of the device of tension

To adjust signs of system of distribution of gas

Sequence of check of a tension of a belt of gear

Removal

ORDER OF REALIZATION

1. To withdraw the negative capture of the accumulator.
2. To withdraw an electric heater and desconectar a hose of a covering of thermostat.
3. To install the transmission in the neutral situation and the parking brake fixes the car.
4. There takes away the side a belt so that it will weaken the pins that fix the creator and will move it towards the motor.
5. To install the piston of 1 cylinder in the superior dead point, becoming an end of inclination of a pin, the pulley of fixation of a belt of side, in the direction of the rotation of work up to the etiquette of the superior dead point it does not go with an etiquette in a covering of a ring of advanced fighter of an end of inclination, and the etiquette in a pulley of an axle will not go with an etiquette in a head of the cylinder block. To observe the provision of a rotor of the distributor regarding the distributor's case so that it will discover the distributor who having lifts the screwdriver 2 side that fixes supports of triangular form and having unscrews 2 screws of the fixation of a covering.
	6. To unscrew the pins that fix a covering of a belt of gear, to reject it to the part and to dispatch it and to withdraw it.
7. To weaken a tension of a belt of gear, in the beginning that having unscrews a pin with an internal hexagon (s=6 key) in the block of tension of belt, and soon a pin with a head of six sides (s=16) and spring resistance overcoming, to tilt the block of a tension and to unscrew completely pins.
8. To unscrew a pin of the fixation of a pulley of an auxiliary belt and to withdraw a pulley of belt of an end of inclination. If the gear belt only is withdrawn of an axle pulley, then it is not necessary to withdraw a pulley of an end of inclination. For an exception of a provorachivaniye of an end of inclination unscrewing a pulley it is necessary to register a pendulum of teeths of a gear garland or to include the fifth transfer and in the spectator to hold tight against the stop a brake of foot.
9. To withdraw a pulley of a belt of auxiliary driving.
10. To withdraw the lavador of direction before a pulley of driving of a belt of gear.
11. To take away a belt of gear, previously having observed the direction of his rotation.
Prevention It is impossible to turn the motor of a pulley of axle as it can destroy a belt. In the presence in a slits belt, aspects of oil or damages of teeths, the belt has to be substituted.

Installation

ORDER OF REALIZATION

1. To check the coincidence of etiquettes in a pulley of the axle and a head of the cylinder block. If necessary etiquettes it will go together.
2. To establish an intermediary end so that the etiquette in a rotor of the distributor works hard on an etiquette in the edge of the distributor. It is previously necessary to discover the distributor, when 2 lifted the screwdriver side that fixes supports of triangular form and having it unscrews 2 screws of the fixation of a covering.
3. To establish a belt of gear in a pulley of an end of inclination and there insists on the doubled one to an end an auxiliary pulley of a belt of side.
4. To establish a belt of gear in a pulley of an axle and to weaken the block of tension of belt.
5. To light two turns an end of inclination of a pulley of a belt of side so that the block of a tension became in a gear belt and to hold tight the block of tension: in the beginning a pin with a head of six sides, and soon with an internal hexagon.
6. To become an end of inclination in 2 turns and to check the agreement of etiquettes in a pulley of an axle, a rotor of the distributor of the ignition and a pulley of a belt of side of an end of inclination.
7. To become an end of inclination in 2 turns in the direction of the movement of the pointers of the clock and soon in 60 ° in reverse sense to the movement of the pointers of the clock and to check a tension of a belt using the instrument of measuring of a tension of a belt 21-113 that has to be established in the longest branch of a belt. The normal tension of a belt corresponds 4-5 unities, for the belt that was in the use and 10-11 unities of a new belt (to see the rice. Sequence of check of a tension of a belt of gear).
	8. The absence of the instrument of measuring of a tension of a belt is possible to define a tension, becoming a big belt and an index finger. The tension is considered the best applying the effort moderated the belt to light 90 °.
9. To establish a covering of a belt of gear.
10. To establish a distributor's covering of ignition.