Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
-3.1. Motor of OHC
3.1.1. Technical characteristic
-3.1.2. Service and repair
3.1.2.1. Agreement of the motor
+3.1.2.2. The repair that does not demand the removal of the motor
3.1.2.3. Removal and installation of the motor
+3.1.2.4. Repair of the motor
3.1.2.5. Lubrication system
3.1.2.6. System of ventilation of a case
+3.2. Motor of DOHC
+3.3. Motor of V6
+3.4. Systems of ignition and management of motor
+3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment
|
Knots of motor of ONS
1 - final collector,
2 - thermostat,
3 - case of thermostat,
4 - flattered pulley of the axle,
5 - covering of a belt of gear,
6 - gear belt,
7 - lever,
8 - spring of valve,
9 - head of the cylinder block,
10 - piston,
11 - cylinder block of the motor,
12 - bomb of cooling the liquid,
13 - ignition distributor,
14 - fuel bomb,
15 - side belt,
16 - klinoremenny a pulley in doubled to an end,
17 - the pulley flattered when in it was doubled to an end,
18 - the pulley flattered in intermediary to an end,
|
19 - dispatch the covering of an end of inclination,
20 - dispatch the covering of an intermediary end,
21 - persistent plate of an intermediary end,
22 - intermediary end,
23 - inclination end,
24 - oil bomb,
25 - covering of a head of the cylinder block,
26 - axle,
27 - persistent plate of the axle,
28 - entry collector,
29 - Systems of сапун of ventilation of a case,
30 - oil separator,
31 - sensor of pressure of oil,
32 - oil filter,
33 - behind epiploon of an inclination end,
34 - persistent half of ring of an end of inclination,
35 - case of oil,
36 - cork of unloading of oil |
Elements of fixation of a covering of a head of the cylinder block (old type)
|
|
And, in – plates pressure,
With – oil placing
|
Elements of fixation of a covering of a head of the cylinder block (new type).
|
|
To, B, C, D – plates pressure |
Order of pressure of pins of a covering of a head of the cylinder block
Check of slits of valves
|
|
1 - countersow,
2 - pin agreement,
3 - spring,
4 - came,
5 - empurrador (lever),
6 - it plates,
7 - valve,
8 - spring of valve |
Agreement of a slit of valves
|
|
1 - came,
2 - empurrador of valve,
3 - pin agreement,
4 - countersow |
The check and the agreement of a slit of valves are done in the cold motor.
Agreement of a slit of valves
| ORDER OF REALIZATION |
| 1. To withdraw the filter of air, to mark and desconectar wires of the high voltage of the distributor of captures of spark and ignition. |
| 2. To discover a head of the cylinder block, having unscrewed ten pins of his fixation (like debit being, the return shown in the rice. Order of pressure of pins of a covering of a head of the cylinder block). |
| 3. To unscrew taken of spark of the simplification of a provorachivaniye of an end of inclination of the motor. |
| 4. To become an end of inclination (in the direction of his rotation of work) before the installation of a came of the investigated valve. |
| 5. Through the probe to check a slit between an empurrador and a came of this valve (to see the rice. Check of slits of valves). The slit measured in a cold condition of the motor between a nucleus of the valve and his empurrador will do 0,20 mm of the valve of entry and 0,25 mm of the end. |
| 6. In case of the necessity it is necessary to adjust a slit of valve, when a countersow unscrewed and like turn seized a pin of the agreement of a slit (3) (to see the rice. Agreement of a slit of valves). |
| 7. To check in the same way and if necessary slits of other valves it will adjust. |
| 8. After check and agreement of slits of valves to establish a front covering with the new placing and to hold tight the corresponding moments ten pins of the fixation of a covering of a head of the cylinder block in the order shown in the rice. Order of pressure of pins of a covering of a head of the cylinder block. |
| 9. To crush new captures of spark. |
| 10. Wires of the high voltage adhere to a distributor of captures of spark and ignition. |
| 11. To install the filter of air. |
|
|
|
