FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+ 1.1. Identification of the car
- 2. Maintenance
   2.1. Frequency of service of cars
   2.2. Each one 10.000 km or once in a year
   2.3. Each one 40.000 km
   2.4. Each one 60.000 km or during 2 years
   2.5. Check of level of oil of motor
   2.6. Substitution of oil of motor and filter
   2.7. Places of possible hole of oil of motor and his definition
   2.8. The check of the level and substitution of cooling the liquid
   2.9. Check of tension of the system of cooling
   2.10. Taken of spark
   2.11. Substitution of the filter of air
   2.12. Substitution of the filter of fuel
   2.13. Substitution of the valve of ventilation of a case of the motor
   2.14. Liquid check in the system of air conditioning
   2.15. Check of level of oil in the transmission
   2.16. Check of level of oil in the rear bridge
   2.17. Check of a condition of a protective covering of an end of power
   2.18. The agreement of a brake carves in the automatic exchange
   2.19. Check of a condition of halls and rear shoes of brake
   2.20. Check of level and substitution of fluid of brake
   2.21. Check of a condition of a support of the triangular form of interruption
   2.22. Check of level of liquid in system of the amplifier of direction
   2.23. The cleaning of a drain of the condensed one that is formed during the operation of the condicionador
   2.24. Recommendations on motor oils
   2.25. Specifications
+3. Motors
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

2.8. The check of the level and substitution of cooling the liquid

GENERAL INFORMATION

The cork of the unloading of cooling the liquid in an electric heater (motor of V6)

The cork of the unloading of cooling the liquid is specified by an arrow.

The screw of removal of air in the superior part of the thermostat (motor of OHC)

The screw of the removal of air is specified by an arrow.

If like the cooling of the liquid mixture of concentrated "Super more 4" and water is in use it must not do the substitution of cooling the liquid.

The control of the level of cooling the liquid has to happen constantly, but at least 1 time in a month.

To apply the liquid that cools only, what is a mixture of the distilled water and antifreeze to a dolivka.

Prevention

In case of the emergence it is possible also to add the clean water, but at the same time in the time as short as possible it is necessary to modify the density of cooling the liquid or substituting it.

The level of cooling the liquid will be in a wide tank between etiquettes "of the MINUTE" and "MAX" in the cold motor.

To add the liquid of cold cooling only in the cold motor.

Expand of cooling the liquid

Motor of OHC	8 l
The motor DOHC with the carburator	7,9 l
The motor DOHC with injection of fuel	7,3 l
Motor of V6	8,5 l
The diesel engine up to September of 93 g.	11,0 l
The diesel engine after September of 93 g.	7,0 l

To do the substitution of cooling the liquid each of 2 years.

ORDER OF REALIZATION

1. To unscrew a covering of a wide tank.

Prevention

It is possible to unscrew a covering only in a temperature below of 40 °C, otherwise it is possible to catch serious burns.

2. To install the corresponding container below an electric heater.

3. In the interior of the car to install the regulator of temperature of heater in the provision of the very temperature.

4. To unscrew a cork of the unloading of cooling the liquid in the lowest part of an electric heater and fusing the liquid.

5. To install the corresponding container below the cylinder block.

6. In the cylinder block to unscrew a pin of the unloading of cooling the liquid and fusing the liquid.

7. After the realization of the unloading to wash out the system of cooling, directing a pure current for a wide tank and to keep on washing until the clean water does not appear of an exit of the lowest tank of an electric heater.

8. After washing itself of the system to crush at the place they drain traffic jams of traffic.

9. To do the stuffing of the system of cooling for a mouth of a wide tank up to the allocation of stops of air blisters.

10. To begin the motor and to heat it up to the work temperature. In the course of be heating of the motor to control the level of cooling the liquid and if necessary it adds.

11. To establish a covering of a wide tank.

12. After cooling of the motor to check the level of cooling the liquid.