FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car



Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   -3.3. Motor of V6
      3.3.1. Technical characteristic
      3.3.2. The repair that does not demand the removal of the motor
      3.3.3. Removal of the motor
      +3.3.4. To be demolished and check of details of the motor
      -3.3.5. Modifications in a drawing of motors V6 2,4 and 2,9 dm3
         3.3.5.1. Removal of the motor
         3.3.5.2. Leaders of the cylinder block
         3.3.5.3. To be demolished and meeting of a head of the cylinder block
         3.3.5.4. Substitution of a chain of the walk of the mechanism of distribution of gas
         3.3.5.5. Agreement of a slit of valves
         3.3.5.6. Oil bomb
   +3.4. Systems of ignition and management of motor
   +3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment


bfe6b27a


3.3.5.4. Substitution of a chain of the walk of the mechanism of distribution of gas

GENERAL INFORMATION

Superior covering of an electric heater, plastic support of triangular form and pin

Pin of fixation of a support of the triangular form of interruption of a tube of the system of cooling

Installation of a natyazhitel of a chain

Launch of a diver of a natyazhitel of a chain

Fixation of a diver of a natyazhitel of a chain

Pin of the mechanism of a tension of a belt of driving of the creator

Pin of the mechanism of a tension of a belt of driving of the bomb of the amplifier of direction


ORDER OF REALIZATION
1. Turn of an end of inclination of the central pin of the fixation of a quencher of fluctuations tortional, to install the piston of 1 cylinder in a point of ignition (12 ° before VMT). The fairness of the installation can happen, when discovered the distributor of ignition, at the same time the rotor of the distributor has to go with the contact of the wire of high voltage that goes to the cylinder number 1.
2. To withdraw a weight they connect of the accumulator.
3. To discover the filter of air together with the sensor of a draft and hoses.
4. To discover a mouth maslozalivny.
5. To fuse the liquid that cools of the cooling system.
6. Desconectar a hose of the connection of the water bomb and a wide tank.
7. To withdraw the superior covering of an electric heater and an electric heater.
8. To remove the supporter of a nave of the water bomb.

Prevention

The nut of the fixation of the supporter has the left woodcarving.


9. Desconectar hoses of system of cooling of unions of the water bomb.
10. To unscrew a pin of the fixation of a support of the triangular form of interruption of a hose of the system of cooling of an advanced covering.
11. To take away a belt of auxiliary driving.
12. To unscrew 4 pins and to withdraw a pulley of an end of inclination.
13. To blockade an end of inclination of a garland of gear of a pendulum, to unscrew the central pin of the fixation of a quencher of fluctuations tortional and to withdraw it, using an artist of streaptise specially.
14. To fuse the oil of motor of the motor.
15. Enclose Desconectar, to unscrew and to remove an author.
16. Care that has, the mechanism that lifts the load to lift the motor, and soon in order that bearers of the motor unscrew.
17. To check what the steering-wheel establishes in the provision of the movement straightly ahead and painting or a marker to observe the provision of the lowest collar of an intermediary end and wheel of gear of directing the transfer, soon desconectar an intermediary end of directing the transfer.
18. Desconectar tubes of brake of a ray of an advanced support of the triangular form of interruption.
19. To support a ray through the corresponding elevator and a wide plank.
20. To unscrew pins of the fixation of a ray to the bottom of the car. To tilt a ray so that the access to a case of oil was launched.
21. To unscrew pins and nuts of the fixation of a case of oil and to take it of bass of the motor.
22. To unscrew 9 pins of the fixation of a covering of the mechanism of the distribution of gas and to discover together with the water bomb.
23. To check that the etiquettes (they are specified by firearms) in asterisks they direct one to other. Otherwise to hold tight an end of inclination before the etiquettes combination.
24. To unscrew and to withdraw a natyazhitel of a chain of the walk of the mechanism of the distribution of gas.
25. To register an asterisk of the axle and to unscrew a pin of the fixation of an asterisk.
26. To withdraw an asterisk of axle together with a chain and to withdraw a chain of an asterisk of an end of inclination.
27. If necessary an asterisk will withdraw of an inclination end with a spline and I send to a chain.
28. To compensate carefully for the inter-connected surfaces of aspects of the old placing.
29. To check the provision of grooves shponochny in the distributive and doubled end. They have of directing one to other.
30. To establish in an inclination end a guide of a chain and an asterisk with a spline.
31. To establish a chain in an asterisk of an end of inclination.
32. To establish a chain in an asterisk of the axle and to install an asterisk together with a chain in the axle, at the same time the spline of the axle will enter in an asterisk groove.
33. To crush a pin of the fixation of an asterisk of the axle.
34. To hold tight a natyazhitel of a chain for which to hold tight a diver of a natyazhitel and to maintain it in this state, having tied the corresponding strip.
35. To establish a natyazhitel of a chain at the place, at the same time having fired to the movie maintaining a diver.
36. To establish the placing of an advanced covering of the mechanism of the distribution of gas.
37. To substitute a ring of fighter of an advanced covering of the mechanism of the distribution of gas.
38. To establish an advanced covering of the mechanism of the distribution of gas.
39. To center an opening in a covering of somewhat the end of inclination, and also at the level regarding the airplane of the installation of a case of oil.
40. To screw pins of the fixation of an advanced covering of the mechanism of the distribution of gas (they are specified by firearms).
41. To compensate carefully for the inter-connected surfaces of the cylinder block and a case of oil.
42. To establish the new placing in flutes of a case of oil.
43. To apply the selante in advanced and rear sieges of a case of oil.
44. To put the interference of structure to unscrew in a pins woodcarving, to establish a case of oil and to crush pins.
45. The edges of work of a hunting concern the oil motor and the surface of quencher of fluctuations tortional inter-connected to a ring and to establish a quencher in an inclination end.
46. To crush the central pin of the fixation of a quencher of fluctuations tortional the corresponding moment.
47. To establish a pulley of an end of inclination.
48. To establish tubes of brake and a ray.
49. An intermediary end adheres to the transfer direction.
50. To establish an author and to join wires.
51. To establish a belt of auxiliary driving.
52. To install the supporter and an electric heater.
53. To establish a covering of the filter of air.
54. To fill out in the oil of motor of motor and liquid what cools in the system of cooling of motor.