FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+ 2. Maintenance
- 3. Motors
   +3.1. Motor of OHC
   +3.2. Motor of DOHC
   -3.3. Motor of V6
      3.3.1. Technical characteristic
      3.3.2. The repair that does not demand the removal of the motor
      3.3.3. Removal of the motor
      +3.3.4. To be demolished and check of details of the motor
      -3.3.5. Modifications in a drawing of motors V6 2,4 and 2,9 dm3
         3.3.5.1. Removal of the motor
         3.3.5.2. Leaders of the cylinder block
         3.3.5.3. To be demolished and meeting of a head of the cylinder block
         3.3.5.4. Substitution of a chain of the walk of the mechanism of distribution of gas
         3.3.5.5. Agreement of a slit of valves
         3.3.5.6. Oil bomb
   +3.4. Systems of ignition and management of motor
   +3.5. Diesel engines
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

3.3.5.2. Leaders of the cylinder block

GENERAL INFORMATION

The process of the leaders' removal of the cylinder block shows up for the motor installed in the car.

Sensor of pressure of oil

The sensor of the pressure of oil is in the left advanced side of the cylinder block.

Dispatch the capture of the sensor of a draft

The agreement of the sensor of the temperature of cooling the liquid

Taken of the turns valve of wasting time

Taken distributor's of ignition

Taken of sensor of temperature of fuel

Hoses of giving (A) and I return (of V) from the fuel

Removal

ORDER OF REALIZATION

1. To withdraw a weight they connect of the accumulator.
2. To fuse the liquid that cools of the cooling system.
3. Desconectar to hose better of an electric heater and a hose of a heater of the case of thermostat.
4. Desconectar air hoses of the case of regulator.
	5. To withdraw two captures of air sensors of current (the firearms specify that they inhale the union).
	6. To withdraw a hose of the ventilation of a case (it is specified by an arrow) of a mouth maslozalivny.
7. To withdraw the case of the filter of air together with hoses and sensors of a draft.
8. Desconectar hoses of a wide tank.
9. Desconectar electric wires of the next elements: – the creator (in the moment of removal of the left head); – the sensor of the temperature of cooling the liquid; – turns valve of wasting time; – potenciômetro of provision of a valve of butterfly; – ignition distributor; – sensor of temperature of fuel; – fuel mouths.
	10. To take away the pressure on the road of fuel (having held tight the valve of the unloading of the pressure) and desconectar fuel oil pipelines.
	11. Desconectar hoses of vacuum of the regulator of the pressure of the fuel, the case of a regulator and of the conector T-shaped.
	12. To withdraw a hose of the ventilation of a case of a front covering (the arrow specified the valve of hose).
13. To unscrew the camera of the elevated pressure and to move it to the part together with a gas pedal thread.
14. To withdraw wires of high voltage of captures of spark and to discover the distributor together with wires.
15. Turn of an end of inclination of the central pin of the fixation of a quencher of fluctuations tortional to install the piston of 1 cylinder in an ignition point (12 ° before VMT) and to remove the distributor of ignition.
16. For the removal of the right head to take away a belt of driving, the creator and the bomb of the amplifier of the direction and a gentle wire to annex to a body.
17. To discover a head of the cylinder block.
	18. To unscrew pins and to withdraw an axle of yokes.
19. To take empurradores and to arrange them in the order that supplies his installation repeated at the places.
20. It to remove a collector when of it entered together with the road of fuel and mouths.
21. For desconectar the reception they exhaust tubes of final collectors.
22. Desconectar the basic tire of a few back left the part of a head.
23. To unscrew taken of spark.
24. Gradually and constantly to unscrew pins of the fixation of a head of the cylinder block in the sequence of the return to what they crush.
25. To withdraw a head of the cylinder block.
26. To withdraw the placing of a head of the cylinder block.

Installation

Sequence of pressure of pins of fixation of a collector of entry

The installation is done in the sequence, the return to the removal, at the same time it is necessary to consider the next moments:

  – to substitute pins of the fixation of a head of the cylinder block with the new;
  – to establish the only new placing of a head of the cylinder block;
  – to apply the selante in the inter-connected surfaces of a collector of entry and chiefs and there insist pins of the fixation of a collector of entry on certain sequence;
  – to heat the motor up to the work temperature and to check the installation of the moment of the ignition;
  – to improve pins of the fixation of a collector of entry in certain sequence.