Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+ 13. Body
- 14. Electric equipment
14.1. Technical characteristic
14.2. Locks of security and alternation
14.3. Unities of electronic control
14.4. System of the central blockade
14.5. System of rates of turns
14.6. Fuel computer
14.7. System of additional control
-14.8. Creator
14.8.1. Removal and installation of the creator
14.8.2. To be demolished and meeting of the creator
14.8.3. Substitution of brushes of the creator and regulator of tension
14.8.4. Bad main functioning of the creator
14.8.5. Agreement of a tension of a belt of side
+14.9. Author
+14:10. I bread to rub of fabric Windshield, knot of rates and lighthouse
14:11. Removal and installation of a combination of devices
14:12. Extern and internal lighting
+14:13. Another electric equipment
+14:14. Electric printers
|
The substitution of the regulator of the tension and one can do the brushes of the creator, without removing the creator of the motor.
It is possible to do the separate removal of brushes and the regulator. CREATOR OF BOSCH
| ORDER OF REALIZATION |
| 1. To withdraw a weight they connect of the accumulator. |
| 2. To unscrew 3 pins and to withdraw the fabric that protects the heat. |
| 3. To unscrew 2 screws of the fixation of the regulator of the tension and, when what has took care, to take the regulator. |
|
4. It checks the length of brushes from graphite (distance E) what will be not less than 5 mm. |
|
5. For the substitution of brushes from coal it is necessary not to weld tokopodvoda, to take worn-out brushes and springs, to establish new brushes with springs in a nest of the regulator and to weld токоподвод so that the brushes length did 10 mm. In the moment of the solder not to allow the blow of flux and solder in токоподвод, except the place of the solder (1 – you brush, 2 – springs of a clip of brushes, 3 – the brushes bearer). |
| 6. To check the tranquillity of the movement of brushes in the bearer. |
|
LUCAS GENERATOR
| ORDER OF REALIZATION |
| 1. To withdraw a weight they connect of the accumulator. |
| 2. To withdraw the fabric that protects the heat. |
| 3. To withdraw the capture with wires of the creator. |
| 4. To unscrew a rear cape of the creator. |
|
5. Desconectar wires of the regulator, to unscrew a plate that is joined, the screw of fixation of the regulator and to take the regulator (1 – I ponder, 2 – plastic placing, 3 – plate that is joined, 4 – the regulator). |
|
6. To unscrew screws (they are specified by an arrow) the fastenings of brushes from graphite and to take brushes of the bearer. |
| 7. To check the length of brushes from graphite that will be not less than 5 mm. |
|
CREATOR OF MOTOROLA
| ORDER OF REALIZATION |
| 1. To withdraw a weight they connect of the accumulator. |
| 2. To withdraw the fabric that protects the heat. |
| 3. To withdraw the capture with wires of the creator. |
|
4. To unscrew the regulator (A) and desconectar 2 wires (they are specified by firearms). |
|
5. To unscrew the screw of the fixation of the bearer of brush. |
|
6. The brush bearer unscrews and, carefully turning it on the outside, to take of the creator (1 – graphite brush, – I contact 2). |
| 7. To check the length of brushes from graphite that will be not less than 4 mm. |
|
|
|
