FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+ 13. Body
- 14. Electric equipment
   14.1. Technical characteristic
   14.2. Locks of security and alternation
   14.3. Unities of electronic control
   14.4. System of the central blockade
   14.5. System of rates of turns
   14.6. Fuel computer
   14.7. System of additional control
   +14.8. Creator
   +14.9. Author
   +14:10. I bread to rub of fabric Windshield, knot of rates and lighthouse
   14:11. Removal and installation of a combination of devices
   14:12. Extern and internal lighting
   +14:13. Another electric equipment
   +14:14. Electric printers

14:12. Extern and internal lighting

MAIN LIGHTHOUSE

Substitution of a bulb of driving and passage of ray

ORDER OF REALIZATION

1. To open a monk's hood.
2. To become a rear cape of a lighthouse in reverse sense to the movement of the pointers of the clock and to withdraw it.
	3. Desconectar to electric capture of a bulb and a spring armband holds tight cushions (they are specified by firearms).
	4. To take a bulb (it is specified by an arrow) of a lighthouse.
5. To establish a new bulb so that the edges of the bearer of a bulb entered in grooves of a reflector of a lighthouse and to fix for a spring armband.
Prevention There prohibits to concern strictly a cylinder from glass of a bulb barehanded. Otherwise it is necessary to rub a cylinder of bulb with the alcohol.
6. To install the capture in a bulb and to close a rear cape of a lighthouse.
7. To check the agreement of the light of lighthouses.

Substitution of a bulb of light dimensional

ORDER OF REALIZATION

1. To open a monk's hood.
2. To become a rear cape of a lighthouse in reverse sense to the movement of the pointers of the clock and to withdraw it.
3. To take on the lowest part of a reflector the bearer of a bulb together with a bulb.
	4. To pull for a bulb (it is specified by an arrow) and to take of the bearer.
5. To move a new bulb for the bearer and to establish the bearer in a reflector.
6. To close a rear cape of a lighthouse.

Substitution of a bulb of the advanced rate of turns

ORDER OF REALIZATION

1. To open a monk's hood.
2. In a driving compartment to unhook the spring maintaining the glass of a lamp of the rate of turns and to take it on the outside.
3. To turn the bearer of a bulb in reverse sense to the movement of the pointers of the clock and to take it of a lamp.
4. A bulb insists on the bearer and on this situation to turn in reverse sense to the movement of the pointers of the clock and to take it.
	5. To insert a new bulb in the bearer (it is specified by an arrow).
	6. To hold tight a bulb against the stop and to turn in this situation in the direction of the movement of the pointers of the clock.
7. The bearer with a bulb to insert in a lamp and to turn in the direction of the movement of the pointers of the clock before the fixation.
8. To insert in the glass of place of a lamp and to fix it during one spring.

Agreement of light of lighthouses

Screws of agreement of light of lighthouses

1 - the screw of agreement of light in the vertical airplane,

2 - the screw of agreement of light in the horizontal airplane

The modification of the installation of the light of the main lighthouses is executed alternatively of the screws located in a rear part of lighthouses (available of a driving compartment).

In lighthouses of the agreement in the vertical airplane the lowest screw, and for the agreement it serves in the horizontal airplane – the superior screw.

Entry conditions:

  – the wheels tires have to be pumped up to the necessary size of the pressure of air in them;
  – the car with a tank full of the fuel has to be loaded only weighing 75 kilograms in the session of the driver;
  – in front of the car there are necessary several times press strongly for the corresponding placing of elastic elements of a support of the triangular form of interruption

Agreement of a ray of light of lighthouses

Scheme of agreement of lighthouses

E - light edge,
In – the center of a light current,
With – a zone of lighting that passes ray,
D - distance of interaxal of lighthouses,

N - height of installation of lighthouses,
Be left – an axle of the car,
X = 120 mm of the main lighthouses and X = 220 mm of lights of thick fog.

ORDER OF REALIZATION

1. To install the car in a clear horizontal surface in the distance of 10 meters of a vertical wall.

2. In a wall to put lines of a marking according to the rice. Scheme of agreement of lighthouses.

3. Lighthouses passer-by to light the ray and to close a lighthouse they improvised the material and to do the agreement of a ray of light of the second lighthouse.

4. To repeat the operation in the agreement of the second lighthouse.

5. It as soon as possible to do the agreement of the light of lighthouses in the special equipment.

Substitution of a bulb of an additional lighthouse

ORDER OF REALIZATION

1. To open a monk's hood.
	2. To withdraw a plastic covering of the superior part of a lighthouse, previously having launched clips of wire (firearm).
3. To hold tight and two wire armbands lead to the part.
4. To take a bulb and desconectar the electric capture.
	5. To join the capture of a new bulb and to establish a bulb (it is specified by an arrow) so that the edges of the bearer of a bulb entered in grooves of reflector of lighthouse.
Prevention There prohibits to concern strictly a cylinder from glass of a bulb barehanded. Otherwise it is necessary to rub a cylinder of bulb with the alcohol.
6. To fix a bulb for two wire armbands.
7. To establish and to register a plastic covering.
8. To check the agreement of the light of lighthouses.

Substitution of a bulb of an advanced light of thick fog

Bulb of an advanced light of thick fog

E - screws of fixation of a lighthouse,

With – the screw of agreement of light of lighthouse

ORDER OF REALIZATION

1. To unscrew two screws of two parties of a lighthouse and to take a lighthouse of a nest.

2. Of the rear party of a lighthouse to hold tight a spring armband of a bulb and to take it to the part.

3. To take a bulb and to call - of the electric capture.

4. To establish a new bulb so that the edges of the bearer of a bulb entered in grooves of a reflector of a lighthouse and to fix for a spring armband.

Prevention

There prohibits to concern strictly a cylinder from glass of a bulb barehanded. Otherwise it is necessary to rub a cylinder of bulb with the alcohol.

5. To join the electric capture.

6. To establish a lighthouse in a nest and to fix for screws.

7. To check the agreement of the light of lighthouses.

Prevention

The agreement of the light of a light of thick fog in the vertical airplane is done by the rotation of the screw located in the superior part of a lighthouse.

Substitution of a bulb of the coach of side of turns

ORDER OF REALIZATION


1. To turn the glass of the coach of turns in the direction of the movement of the pointers of the clock and to take the coach of turns of a body.
2. To turn the glass of the coach of turns in reverse sense to the movement of the pointers of the clock regarding the bearer of a bulb and to withdraw it.
3. Having pulled for a bulb, to take it of the bearer.
4. To establish a new bulb in the bearer.
5. The bearer to establish the glass of the coach of acende and to register it turn in the direction of the movement of the pointers of the clock.
6. To install the coach of turns in a body and to register it they turn in reverse sense to the movement of the pointers of the clock.

SUBSEQUENT LAMP

Bulbs substitution

Bulbs agreement in the bearer

1 - bulb of the rear rate of turns (12V, 21W),

2 - the fires bulb of braking (12V, 21W),

3 - bulb dimensional (12V, 10W),

4 - behind thick fog bulb (12V, 21W),

5 - bulb of a support (12 V, 21 W)

The substitution of bulbs of a lamp of a support is done from the baggage compartment.

ORDER OF REALIZATION

	1. To discover (firearms), final lamps of the relevant party. In the right side it is necessary to call - of the electric capture.
2. One to hold tight in the direction to other armbands and to take the bearer of bulbs of a lamp.
3. For the substitution of a defective bulb in order that a bulb insists on the bearer and on this situation to turn it in reverse sense to the movement of the pointers of the clock and to take of the bearer.
4. To insert a new bulb in the bearer, to hold tight it against the stop and to turn in this situation in the direction of the movement of the pointers of the clock.
5. To establish at the place and to register the bearer of bulbs.
6. Final lamps establish the covering.

Removal of a rear lamp

ORDER OF REALIZATION

Car hoof with bodywork
1. To discover of the baggage the compartment of a rear lamp.
	2. There unscrew six nuts (they are specified by firearms) the fastenings of a rear lamp.
3. To take a lamp on the outside of the car and to withdraw the capture.
Body Sedan
	4. To withdraw a few articles of tapestry of haulage company of baggage of the necessary party.
	5. To unscrew nuts (2) fastenings of a rear lamp. To take a lamp on the outside of the car and to withdraw the capture (1).

Substitution of a bulb of lighting of plate of register

ORDER OF REALIZATION

	1. To insert an edge of the fine screwdriver below the consolidation of rubber of a lamp and to hold tight an armband (of 1) of a plafond and to take a lamp of bumpers.
2. To turn the bearer of a bulb in reverse sense to the movement of the pointers of the clock and to take it.
3. Having pulled for a bulb, to take it of the bearer.
4. To establish a new bulb in the bearer.
5. To establish the bearer of a bulb in a lamp and to turn against the stop in the direction of the movement of the pointers of the clock.
6. To establish a lamp in bumpers before his right fixation.

Substitution of illuminating lamps of the hall

ORDER OF REALIZATION

To insert an edge of the fine screwdriver in the right side below the block of the lighting and having held tight the screwdriver to take it of a nest. In case of the removal of the lamp to read to insert the screwdriver of down in an average part of the block of the lighting. To do the substitution of lamps and to install the block at the place. If necessary it is possible to draw in the contacts maintaining a bulb.

Substitution of illuminating lamps of a mirror

ORDER OF REALIZATION

	1. To insert an edge of the fine screwdriver in the right side below a frame of a mirror and, having held tight the screwdriver, to take a frame of a nest.
2. To do the substitution of a bulb and to establish a frame at the place. If necessary it is possible to draw in the contacts maintaining a bulb.

Substitution of bulbs of the alarming system of open doors, lighting of space of legs and compartment of baggage

ORDER OF REALIZATION

1. To insert an edge of the fine screwdriver below a plafond of a bulb and, having held tight the screwdriver, to take a plafond of a nest.
	2. To take away a bulb and to substitute it (in the drawing – the substitution of an alarming bulb of open doors).
3. To substitute a bulb and to establish a plafond before his right fixation.

Removal and installation of a lighthouse and svetorasseivatel

ORDER OF REALIZATION

1. To open a monk's hood.
2. To withdraw a weight they connect of the car.
Prevention At the same time the information in electronic memory devices goes out of the memory.
3. Desconectar to electric capture near to a lighthouse. In the presence of the ticket inspector of the light of lighthouses also for desconectar of him the electric capture.
4. To withdraw a lamp of the rate of the turn.
5. To withdraw the placing of rubber located between bumpers and a headlight.
6. To withdraw the front guard fixed by two screws.

7. To unscrew the top (it is specified by an arrow in the drawing on the right) and more low (it is specified by an arrow in the drawing in the left) the pins of the fixation of a lighthouse.
	8. The fastenings of a lighthouse to unscrew lightly a nut of side (it is specified by an arrow) and to take a lighthouse, having advanced it and to the part.
9. To withdraw all the bulbs of a lighthouse.
	10. Insertion in grooves of the rear party of a lighthouse to screwdriver and his turn, to withdraw spring clips of the fixation from glass.
11. To withdraw the glass of lighthouse together with the placing hunting.

Substitution of the lamp of lighting of switches

The lamps substitution can be done after the removal of the doorknob of the switch.

ORDER OF REALIZATION

	1. The switch withdraws the doorknob of the access to a lamp (it is specified by an arrow).
2. To substitute a bulb.

Substitution of the lamp of lighting of a box of article

ORDER OF REALIZATION

	1. To open a box of article (the arrow specified an agreement of the lamp of lighting of a box of article).
2. To unscrew two screws and to take the block of the switch and a lamp.
3. To take a lamp of the block and to establish new.

Substitution of the lamp of lighting of an ashtray

ORDER OF REALIZATION

	1. On an ashtray to withdraw a box or the radio-receiver (the arrow specified an ashtray that illuminates agreement of lamp).
2. Through the opening opened to take the bearer of a bulb, spreading it out on the outside, or screwdriver carefully to separate it of a covering.

Substitution of a lamp of lighting of the list of a heater

ORDER OF REALIZATION

1. To withdraw a panel fringing.
2. To withdraw the doorknob of the management of a heater, having pulled it in himself.
3. Through the screwdriver to withdraw the list of heater.
	4. To take a bulb (it is specified by an arrow) of the bearer.
5. To substitute a bulb.

Substitution of a lamp of lighting of the selector of the automatic exchange

ORDER OF REALIZATION

1. To unscrew the selector's doorknob.
2. To remove a selector who fits.
3. To pull out two supports of the triangular form of the fixation of a scale of the selector and to withdraw a selector's scale.
4. To unscrew four screws and to withdraw the plate of direction.
	5. To remove the bearer and the selector's lighting substitutes a lamp (it is specified by an arrow).

Substitution of a lamp of lighting of the switch of the alarming light system

ORDER OF REALIZATION

1. To withdraw the superior covering of a column of direction, previously having unscrewed three screws.

2. To check that the switch is in the situation "Vykl" soon to withdraw the button of switch.

3. To take and to insert a new lamp.

4. To install at the place the button of the switch and the superior covering of a column of direction.

Substitution of a lamp of lighting of hours

If the hours they are determined in a devices combination, the substitution is made similar to the substitution of bulbs of control.

ORDER OF REALIZATION

1. In case of the installation of hours with the superior agreement, for the substitution of a bulb of the lighting of hours it is necessary to withdraw the superior consolation.
2. For the removal of the superior consolation to withdraw a plafond of the lighting of the hall and the doorknob of the opening of the hatch, to unscrew two screws of the fixation of an advanced part of the consolation, to lower an advanced part of the consolation I lower and to move behind.
3. For the access to a lamp to withdraw a rear cape of hours, previously having unscrewed two screws.
	4. To substitute a lamp (it is specified by an arrow) with the fixation of bayonetny.
5. To establish a rear cape of hours and soon the superior consolation.