FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+ 13. Body
- 14. Electric equipment
   14.1. Technical characteristic
   14.2. Locks of security and alternation
   14.3. Unities of electronic control
   14.4. System of the central blockade
   14.5. System of rates of turns
   14.6. Fuel computer
   14.7. System of additional control
   +14.8. Creator
   +14.9. Author
   +14:10. I bread to rub of fabric Windshield, knot of rates and lighthouse
   14:11. Removal and installation of a combination of devices
   14:12. Extern and internal lighting
   -14:13. Another electric equipment
      14.13.1. Removal and installation of switches, motors and sensors
      14.13.2. System of additional control
      14.13.3. Removal and installation of the radio-receiver
      14.13.4. Removal and installation of loudspeakers
      14.13.5. System of the alarming system that is antidragged
   +14:14. Electric printers

14:13. Another electric equipment

Substitution of the motor of the ticket inspector of light of lighthouses

The motor of the ticket inspector of the light of lighthouses is installed of the rear party of a lighthouse and fixes through a clip of bayonetny.

ORDER OF REALIZATION

1. To withdraw the electric capture of the motor of the ticket inspector of the light of lighthouses.
	2. The motor of the ticket inspector insists on the direction of a lighthouse and on this situation to turn the motor in the direction of the movement of the pointers of the clock of a right lighthouse or in reverse sense to the movement of the pointers of the clock of a left lighthouse.
3. Through an opening in case of a lighthouse to hold tight the lever of the end of agreement of fixation and to take the motor of the ticket inspector of a lighthouse.
4. The installation is done in the sequence, the return to the removal.

Removal and installation of hours

ORDER OF REALIZATION

1. To withdraw the superior consolation.

2. For the removal of the superior consolation to withdraw a plafond of the lighting of the hall and the doorknob of the opening of the hatch, to unscrew two screws of the fixation of an advanced part of the consolation, to lower an advanced part of the consolation I lower and to move behind.

3. To withdraw a rear cape of hours, previously having unscrewed two screws.

4. To unscrew two screws of the fixation and to take hours.

5. To install hours in the consolation.

6. To establish a rear cape of hours and soon the superior consolation.

Removal and installation of easier

ORDER OF REALIZATION

1. To withdraw a weight they connect of the accumulator.

Dispatch easier

2. In models the easiest with the increased level of the finish of the hall of the access to withdraw a bedcover of the central consolation of the radio-receiver.

3. In models with the usual finish of the hall of withdrawing the radio-receiver.

4. Desconectar of the easiest of a wire and to take it of the outstanding ring.

Backwards easier

5. To withdraw the doorknob of the management of a heater.

6. To withdraw the list of the back I console central office, previously having unscrewed two screws of the fixation.

7. Desconectar of the easiest of a wire and to take it of the outstanding ring.

8. The installation is done in the sequence, the return to the removal.

Removal and installation of a solid sign

Two solid signs are installed in the car. The solid sign of the tone of high throw is established for the right wing of an electric heater and is available of a driving compartment. The sign of sound of low frequency is established of down and for the left of an electric heater and is available of below of a driving compartment.

ORDER OF REALIZATION

1. To unscrew a nut of fixation or a pin and to withdraw the lavador vibroextinguishing.

2. To withdraw electric captures and to take a solid sign.

3. The installation is done in the sequence, the return to the removal.

Removal and installation of the switch of a solid sign, contact with rings and brushes

ORDER OF REALIZATION

1. To withdraw a weight they connect of the accumulator.
2. Withdraw the central bedcover of a steering-wheel.
	3. There unscrew three screws (they are specified by firearms) the fastenings of a support of the triangular form of the switch of a solid sign.
4. To withdraw the electric capture and to take a support of the triangular form of the switch of a solid sign.
5. To withdraw a steering-wheel.
6. Not to bend ears of the fixation of the contact concerns the lowest part of a steering-wheel, for desconectar of a support of triangular form and to withdraw rings of contact.
7. To withdraw the top and the lowest coverings of the column of direction.
8. Desconectar wires of brushes of a solid sign.
	9. Care that has, to hold tight out the block of brushes to screwdriver inserted below the inferior edge of the block.
10. The installation is done in the sequence, the return to the removal.

Removal and installation of elements of a heater of seats

ORDER OF REALIZATION

1. To withdraw a seat.
2. To withdraw a few articles of tapestry of seat.
3. To observe the direction of an agreement of an element of heating, soon to withdraw clips of wire and the insulating tape that fixes an element to the session.
4. To establish clips in a new element.
5. To establish a new element of heating for the party advanced to the rubber of foam of pillow. To fix an element of heating for clips of wire and a strip. To check that the heating element gives in in the annexe of the load to the session.
6. To establish a few sitting articles of tapestry.
7. To establish the session.
	8. The regulator (firearm) has to address for the party advanced to the rubber of foam of pillow.

Removal and installation of group of contact of the lock of ignition

ORDER OF REALIZATION

1. To withdraw a weight they connect of the accumulator.
2. To withdraw the top and the lowest coverings of the column of direction, previously having unscrewed six screws of the fixation.
	3. To put the group of contact in freedom of the lock of the ignition (firearm), having pulled out two ears of fixation.
4. During the installation to check that the interruption of the center of the group of contact of the lock of the ignition if fez up to to an edge in the lock.
5. To join the group of contact of the lock of the ignition and to hold tight it at the place to a zashchelkivaniye of fixing ears.
6. To join a weight they connect to the accumulator and to check the efficiency of the group of contact of the lock of the ignition soon to establish coverings of a column of direction.