FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+6. Union
+7. Transmissions
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+ 13. Body
- 14. Electric equipment
   14.1. Technical characteristic
   14.2. Locks of security and alternation
   14.3. Unities of electronic control
   14.4. System of the central blockade
   14.5. System of rates of turns
   14.6. Fuel computer
   14.7. System of additional control
   +14.8. Creator
   +14.9. Author
   +14:10. I bread to rub of fabric Windshield, knot of rates and lighthouse
   14:11. Removal and installation of a combination of devices
   14:12. Extern and internal lighting
   -14:13. Another electric equipment
      14.13.1. Removal and installation of switches, motors and sensors
      14.13.2. System of additional control
      14.13.3. Removal and installation of the radio-receiver
      14.13.4. Removal and installation of loudspeakers
      14.13.5. System of the alarming system that is antidragged
   +14:14. Electric printers

14.13.1. Removal and installation of switches, motors and sensors

LUZ'S SWITCH, SUPPORTER'S SWITCH OF HEATER

ORDER OF REALIZATION

1. To withdraw a weight they connect of the accumulator.

2. To withdraw the doorknob of switch, having pulled it in himself.

3. To pull out two armbands, to take the switch of the panel.

4. Desconectar the capture and to withdraw the switch.

5. The installation is done in the sequence, the return to the removal.

REGULATOR OF LIGHTING OF DEVICES

ORDER OF REALIZATION

1. To unscrew four screws and to withdraw a decorative bedcover of a combination of devices.
	2. To take the regulator of the lighting of devices (it is specified by an arrow) and desconectar the capture.
3. In case of the bad functioning the regulator of the lighting of devices is not in the repair and is subject to the substitution.

SWITCH OF MANAGEMENT OF THE PROVISION OF THE MIRROR AND SWITCH OF ELECTRIC STEKLOPODJMNIK

ORDER OF REALIZATION

1. The screwdriver with a fine edge to hook the switch up and to take it of an armchair arm.
	2. Desconectar the capture and to withdraw the switch (it is specified by an arrow).
3. The installation is done in the sequence, the return to the removal.

SWITCH OF RATES OF TURNS AND SWITCH OF CLEANERS AND LAVADORES OF THE WINDSHIELD

ORDER OF REALIZATION

1. To withdraw a weight they connect of the accumulator.
2. To withdraw the central bedcover of a steering-wheel.
3. To withdraw the top and the lowest coverings of the column of direction, previously having unscrewed six screws of the fixation.
	4. Desbloquear a steering-wheel and to turn it for what the access to two open screws (they are specified by firearms) the fixation of the switch. To unscrew screws.
5. To take the switch of a column of direction and desconectar the capture.
6. During the installation to check the operation of the switch before establishing the coverings of the column of direction and the central covering of a steering-wheel.

THE SWITCH OF INDIVIDUAL LIGHTING IN THE TORTURE OF DOORS

ORDER OF REALIZATION

1. To unscrew a screw and to take the switch.

2. To fix wires for a thread or a clothespeg so that they managed in a torture, and after this to call - of the capture.

3. Before the installation to polish a point of the turn of the button of the switch with the technical vaseline.

SUPPORT OF LUZ'S SWITCH (MANUAL TRANSMISSION)

The switch of the light of a support is in the right side of the transmission.

ORDER OF REALIZATION

1. To lift and to register an advanced part of the car in supports.

2. To withdraw a wire of the switch, to compensate carefully for the switch and the adjacent place to the switch and to unscrew the switch.

3. After the installation of the switch to check what the wire of the switch locates in the sufficient removal of a tube of leak.

SWITCH OF OPENING OF THE HATCH

ORDER OF REALIZATION

1. Care that has, the screwdriver with a fine edge to take away the switch of the superior consolation.

2. Desconectar the capture and to withdraw the switch.

SENSOR OF CONNECTION OF THE BRAKE OF EMERGENCE

ORDER OF REALIZATION

1. To withdraw a covering of rubber and, if necessarily, the central consolation or the decorative list of the sensor.
2. To withdraw a wire of the sensor.
	3. To unscrew two screws and to withdraw the sensor.

LUZ'S SWITCH OF THE BRAKE

ORDER OF REALIZATION

1. To withdraw the articles of tapestry below the panel of the driver fixed by plastic clips.
2. To withdraw of the wire switch.
3. To turn the switch in 90 ° in reverse sense to the movement of the pointers of the clock and to withdraw it of a support of the triangular form of the fixation of a pedal of a brake.
	4. During the installation to hold tight a pedal against the stop, to insert the switch and to face in the direction of the movement of the pointers of the clock his fixation. To launch a pedal and to check that at least 2 mm of a stick of the switch were visible.

SENSOR OF PRESSURE OF OIL

The sensor of pressure of oil in all the motors, except DOHC, is located in the left side of the cylinder block. In motors DOHC the sensor of the pressure of oil is located in the advanced left side of the cylinder block.

ORDER OF REALIZATION

1. For the simplification of the access to the sensor to move one of oil pipelines to the part.

2. To withdraw of the wire switch.

3. To unscrew and to withdraw the sensor.

4. Before the installation carefully to smooth the sensor and his nest. In a woodcarving of the sensor to apply a fine film of the selante.

5. To install the sensor, to join wires, to begin the motor and to check the tension of the installation of the sensor.

6. To stop the motor and to check the level of oil of motor.

SWITCH OF THE HEATER FROM SUBSEQUENT GLASS

ORDER OF REALIZATION

1. To unscrew four screws and to withdraw a decorative bedcover of a combination of devices.

2. Care that has, an edge of the fine screwdriver to take the switch of a nest.

3. To withdraw the capture of the switch.

SWITCH OF AGREEMENT OF PROVISION OF THE FRONT SEAT

ORDER OF REALIZATION

1. There withdraws the seat which copper lists.
2. The screwdriver with a fine edge to withdraw of the switch of the doorknob of the management.
	3. To unscrew two screws of the fixation, to take the switch and desconectá-lo.

MOTOR OF SYSTEM OF THE CENTRAL BLOCKADE

System of the central blockade of doors

The lock of close of a back door with an eletroímã

ORDER OF REALIZATION

1. To withdraw a weight they connect of the accumulator and to open all the doors.
2. To withdraw a few internal articles of tapestry of a door.
3. Care that has, to withdraw of a door the covering of door of isolation in the field of the installation of the motor of the system of the central blockade.
	4. The fastenings of the motor unscrew two screws (they are specified by firearms) and desconectar the motor of a stick of the control of the lock.
5. To withdraw the electric capture.
6. To withdraw the electric motor. In case of the bad functioning of the motor it has to be substituted as it is not subject to the repair.
7. The installation is done in the sequence, the return to the removal, and is compulsory to install the button of the blockade of doors in the situation "openly", to weaken the screw of the fixation of the internal doorknob, to move the doorknob ahead against the stop and to hold tight the screw.

MOTOR OF WINDOW REGULATOR DRIVE

ORDER OF REALIZATION

1. To withdraw the mechanism of the lifting glass together with the motor.
	2. To check that the spring maintains the lever in the final position (firearm).
	3. To unscrew three pins (they are specified by firearms) and to separate the motor of the mechanism of the lifting glass.
Prevention The inattentive otpuskaniye of one spring can be the reason of damages and wounds.
4. The installation is done in the sequence, the return to the removal.

MOTOR OF AGREEMENT OF PROVISION OF THE SEAT, MOTORS OF ELEVATION AND MOVEMENT OF PILLOW OF THE SEAT

ORDER OF REALIZATION

1. To move a front seat behind against the stop.
2. To unscrew two pins of the fixation of an advanced part of a frame of a seat and to reject a seat behind.
	3. To unscrew two pins (they are specified by firearms) and to withdraw electric motors.
4. To check that the threads of walk of gears of worm move without effort, otherwise also for desconectar an end of the gear of worm.
5. In the moment of the removal only of a motor they take his contacts of knife of the general capture after the removal of the case of the capture.
6. The installation is done in the sequence, the return to the removal.

MOTOR OF MODIFICATION OF THE INCLINATION OF SEATBACK

ORDER OF REALIZATION

1. To withdraw a front seat.
	2. To unscrew two pins of the fixation, desconectar the capture and to take the electric motor of the mechanism of rejection.
3. To install the motor so that the wheel of gear of gear of the electric motor was hooked up with a wheel of gear of mechanism of detour.
4. To join the capture and to fix the electric motor for two pins.
5. The new installation is done in the sequence, the return to the removal.

ELECTRIC MOTOR OF HATCH DRIVE

ORDER OF REALIZATION

1. To withdraw the superior consolation.
	2. To unscrew three pins of fixing (they are specified by firearms), to lower the electric motor, desconectar the capture and to take the alternation.
3. To install the motor so that the wheel of gear of gear of the electric motor was hooked up with a wheel of gear of the mechanism of the management of the provision of a covering of the hatch.
4. To install the alternation, to join the capture and to fix the electric motor for three pins.

SENSOR OF SPEEDOMETER

1 - brown wire,
2 - wire, brown with a yellow strip,
3 - wire, brown with a black strip,

4 - it fuses the contact,
5 - tube isolation,
6 - place of reduction of a brown wire

The walk of a speedometer is transported out of the electric sensor located in the left side of the extension of the transmission.

ORDER OF REALIZATION

1. To lift and to register an advanced part of the car.
2. Below the sensor to install the corresponding container.
	3. To unscrew a pin of fixation (it is specified by an arrow) and to take the sensor of the transmission (1 – mechanical transmission, 2 – the automatic exchange).
4. To call - of the electric capture.
5. During the installation of the new sensor to establish in him of the old sensor a wheel of gear of driving and a clip to cancel, and in models with the automatic exchange and a ring of fighter.
6. If in the old sensor there were two wires, and in new three, to cut a brown wire of the capture and besides that to establish the base.
7. To install the new sensor and to fix it through a new pin (mm M6x25 of the manual transmission and M6x35 of the mm of the automatic exchange). Except the new sensor, the pin also fixes a new ear of the base, the tire of the base of the radio-receiver and a support of the triangular form of fixation of the capture.
8. To join the capture and to fix it in a support of triangular form.
9. To bring the level of oil in the transmission to the standard.

LAMP OF LIGHTING OF THE COMPUTER OF FUEL

ORDER OF REALIZATION

The cars manufactured to 04.1992 g.
1. To withdraw a decorative covering of the panel that fixes four screws.
2. To take carefully the computer of fuel. To withdraw the capture, having pressed it.
	3. To take a cartridge with a bulb, having held tight his passatizham and having turned in reverse sense to the movement of the pointers of the clock. To spread out an old bulb of the chief.
4. The installation of a new bulb is done in the sequence, the return to the removal.
The cars are manufactured of 04.1992 g.
5. Withdraw a decorative covering of the panel that fixed two screws and two clips.
6. To take the regulator of the lighting of devices and desconectar the capture.
7. To withdraw three doorknobs of the management of a heater of the access to screws of the fixation of the list of a heater.
8. To unscrew four screws of the fixation of the list of a heater and to move partially the list.
9. Desconectar been overcome with a heater from glass and the computer of fuel of the list and to withdraw the list.
	10. The fastenings of the computer to unscrew four screws (they are specified by firearms) to the list and to withdraw the computer.
11. To substitute lamps of the lighting of the computer of fuel.

SENSOR OF CURRENT OF FUEL (ONLY MODEL OF CARBURATOR)

The sensor is located in the left fender in a driving compartment.

ORDER OF REALIZATION

1. To withdraw an opportunity of weight of the accumulator.
2. To withdraw the electric capture and tubes of fuel of the sensor.
	3. To unscrew three screws of the fixation of a support of the triangular form of the sensor. To withdraw the sensor together with a support of triangular form.
4. The installation of the sensor is done in the sequence, the return to the removal.