FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+ 6. Union
- 7. Transmissions
   +7.1. Mechanical transmission of five speeds of type of N
   -7.2. Mechanical MT 75 transmission
      7.2.1. Technical characteristic
      -7.2.2. Service and repair
         7.2.2.1. Removal and installation of the transmission
         -7.2.2.2. Desmontagem of the transmission
            7.2.2.2.1. Check and repair of details of the transmission
            7.2.2.2.2. Primary and secondary end
         7.2.2.3. Meeting of the transmission
   +7.3. Transmission A4LD automatic
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

7.2.2.2.1. Check and repair of details of the transmission

GENERAL INFORMATION

End and wheels of gear of the mechanical MT 75 transmission

1 - needle load,
2 - lock the spring ring,
3 - load,
4 - main end,
5 - ring of sincronizador,
6 - needle load,
7 - lock the spring ring,
8 - nave of the sincronizador of 3-4 transfers,
9 - wheel of gear of the 3rd transfer,
10 - remote capture,
11 - wheel of gear of the 2nd transfer,
12 - wheel of gear of the 1st transfer,
13 - secondary end,

14 - wheel of gear of transfer of a support,
15 - wheel of gear of the 5th transfer,
16 - wheel of gear of walk of speedometer,
17 - intermediary end,
18 - axle of a wheel of intermediary gear of transfer of a support,
19 - basic capture of the load of a wheel of gear of transfer of a support,
20 - wheel of intermediary gear of transfer of a support,
21 - I crunch of sincronizador
The numbers of transfers are supplied in black circles (AIR – the transfer of a support; Rio Grande do Sul – straight transfer – 4).

SUBSTITUTION OF LOADS

Size of control of provision of a face of end of the selector

ORDER OF REALIZATION

1. Through an artist of streaptise inercial to take the load (3) (to see the rice. End and wheels of gear of the mechanical MT 75 transmission) a secondary end of a case of transmission.

2. Of a case of the transmission to withdraw a plate of agreement of the load of a secondary end.

3. Through the capture of the corresponding diameter to beat the load of ball of a secondary end in a case of transmission.

4. To withdraw an axle of forks of 1-2 transfers of a case of transmission.

5. To withdraw a ring of fighter of the main axle of the selector.

6. Through the capture of the corresponding diameter to withdraw the load of needle of the main axle of the selector of a case of transmission.

Prevention

In case of the substitution of a case of the transmission it is necessary to arrange the selector so that the distance between his face of end and the airplane of a case did 69 mm (to see the rice. Size of control of provision of a face of end of the selector).

7. Through a nucleus of the corresponding diameter to install the new load of needle of the main axle of the selector of inside a case of transmission.

8. To establish a new ring of fighter of the main axle of the selector in a case of transmission.

9. To arrange a selector's axle in a case of transmission so that his part valtsovanny addressed towards the airplane of condensed case.

10. Through the corresponding nucleus to press against the stop in a transmission they fit in the load of needle of an intermediary end.

11. Through the corresponding nucleus to press against the stop in a transmission they fit in the load of ball of a secondary end.

12. In a case of the transmission to establish a plate of the fixation of the load of a secondary end and to hold tight pins the corresponding moment.

13. Through the capture of the corresponding sizes to withdraw in the direction of an advanced part of a case of the union the load of ball of a main end.

14. To withdraw a ring of spring agreement of the load of needle.

15. Through the capture and the wooden hammer to beat in the direction of a rear part of a case of the union the load of an intermediary end.

16. Through an artist of streaptise to withdraw the load of needle of the main axle of the selector of a case of union.

17. To insert through a nucleus the load of an intermediary end in a case of union. It is not necessary to install the load against the stop, it is necessary to stop the distance of 2 mm of the airplane of flange case of union.

18. To establish a new ring of spring agreement of the load gives ball.

19. Through the capture to install the new load of a main end in a case of union.

CHECK OF THE AXLE OF THE WHEEL OF GEAR OF TRANSFER OF THE SUPPORT

ORDER OF REALIZATION

1. Through the corresponding nucleus to withdraw a pin of agreement of an axle of a wheel of gear of the transfer of a support.

2. To withdraw the basic capture of the load, a wheel of intermediary gear of the transfer of a support and the load of needle of an axle.

3. To check a condition of the taken elements.

4. To put the load of needle, a wheel of intermediary gear of the transfer of a support and the basic capture of the load of an axle.

5. To establish a new pin of agreement.

6. Through the screwdriver to take a ring of fighter of the capture of direction of the load of launch.

7. To establish a new hunting they touch through a nucleus of the corresponding diameter; the fighter edge has to address towards a nucleus.