| 1. To insert an axle of forks of 1-2 transfers in the union of the escorregamento of the sincronizador of 1-2 transfers in the secondary one to an end. |
| 2. To do the intermediary and secondary end and to maintain this knot through a rubber bandage. |
| 3. To establish a wheel of intermediary gear of the transfer of a support so that it will cancel his thickening if it was driving towards a main end. |
| 4. Through the next rubber bandage to maintain this knot. |
| 5. To arrange the whole knot in a case of transmission. |
| 6. There puts a secondary end a wheel of gear of driving of a speedometer together with the remote capture. |
| 7. To check if the intermediary end in a case is established correctly. 16.042 finishes his situation through the adaptation. |
| 8. To insert a rear pin of the fixation of an axle of a wheel of intermediary gear of the transfer of a support and to crush it a hand. |
| 9. To withdraw a wheel of gear of the walk of a speedometer and the remote capture. |
| 10. To insert a magneto in a case of transmission. |
| 11. To withdraw a bandage of rubber. |
|
12. To insert forks of 3-4 transfers, directing a cut for low down, and soon forks of the 5th transfer and transfer of a support. |
| 13. To insert an axle of forks of 3-4 transfers, the 5th transfer and transfer of a support. |
| 14. To establish a case of union in a case of transmission, inserting three supports of 25 mm of thickness between the airplanes of the connection of both cases. |
| 15. Polish the airplanes of the connection with the briefcase that pressuriza. |
| 16. To take three supports and 16.041 joins a case through the adaptation. |
| 17. To insert two pins that join both cases in openings and carefully finally to join them. |
| 18. To insert another eight pins they are joined and to hold tight all the pins the corresponding moment. |
| 19. To install the remote capture and a wheel of gear of a speedometer in a secondary end. |
| 20. Through the capture of the corresponding diameter to establish a new ring of fighter of a flange of the connection of the advanced hinge of the driving axle. |
| 21. To establish a flange of the connection of the advanced hinge of the driving axle in a secondary end. |
| 22. To put the new armband of the fixation of a flange in the rear end of a secondary end, when it polished in the beginning a surface of a woodcarving of a nut with the briefcase that pressuriza. After fixing of a flange of the connection of the advanced hinge of the driving axle to hold tight a nut the corresponding moment. |
23. To polish with the briefcase that pressuriza a woodcarving of pin of selector's cork, to crush a pin and to hold tight it the corresponding moment.
Prevention
 The briefcase that pressuriza must not bring the transmission near.
|
| 24. There insists against the stop on a case the capture of selector's cork. |
| 25. To establish a ball, an empurrador and a spring of a cork of the selector. |
| 26. To polish with the briefcase that pressuriza a woodcarving of cork of selector's cork, to crush a cork in a case of the union and to hold tight it the corresponding moment. |
| 27. To crush an advanced pin of the fixation of an axle of a wheel of intermediary gear of the transfer of a support in a case of union and to hold tight the corresponding moment both pins (they dispatch and behind). |
| 28. To establish a new spring ring of agreement in a main end. |
| 29. To establish a new ring of fighter of the round section in the capture of direction of the load of launch of the union, to install the capture in a case of the union and to hold tight his pins the corresponding moment. |
| 30. To establish the new placing of the round section in a nut of the load of an intermediary end. |
| 31. To put the armband of the load of an intermediary end in front of a case of the union and to hold tight his moment 15-20 nanômetros. |
| 32. To indicate the provision of a nut about a case of the union and to unscrew it in 60 °. |
| 33. To two fuller edges located on this nut. |
| 34. To check if the load of an intermediary end leans in an agreement nut. This nut must not be turned by a hand. Otherwise it is necessary to repeat three last operations after unscrewing of a nut. |
| 35. To establish a plate of the fixation of a nut of the load of an intermediary end and to hold tight a pin of the fixation of the plate of fixation. |
| 36. After imposing of a little quantity of the lubricant in openings of a main end and the capture of direction of the load of launch of the union to install in a main end the load of launch of the union together with the union that puts forks out. |
| 37. To crush traffic jams of traffic of the unloading of oil and to hold tight them the corresponding moment. |
|
38. To fill the transmission of the necessary amount of the corresponding oil of transmissions. |
