Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+ 6. Union
- 7. Transmissions
+7.1. Mechanical transmission of five speeds of type of N
-7.2. Mechanical MT 75 transmission
7.2.1. Technical characteristic
-7.2.2. Service and repair
7.2.2.1. Removal and installation of the transmission
-7.2.2.2. Desmontagem of the transmission
7.2.2.2.1. Check and repair of details of the transmission
7.2.2.2.2. Primary and secondary end
7.2.2.3. Meeting of the transmission
+7.3. Transmission A4LD automatic
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment
|
Case of transmission
1 - case of union,
2 - case of transmission,
3 - cork of stuffing of oil,
4 - cork of unloading of oil,
5 - the capture of direction of the load of launch, |
6 - support of the load of an intermediary end,
7 - switch of lamps of a support,
8 - сапун,
9 - details of walk of speedometer,
10 - flange of an end of production of the transmission |
Mechanism of dislocation of gear, MT 75 transmissions
1 - axle of forks of 3-4 transfers, 5th transfer and transfer of a support,
2 - axle of forks of 1-2 transfers,
3 - forks of 3-4 transfers,
4 - forks of the 5th transfer and transfer of a support,
5 - taken,
6 - forks of 1-2 transfers,
7 and 8 – selectors, |
9 - cork blockade,
10 - prick,
11 - prick,
12 - management finger,
13 - taken of management,
14 - the finger of blockade that does impossible simultaneous inclusion of two transfers
15 - you plate |
Vision of front of case of union
|
|
1 - plate of fixation of a nut,
2 - nut of the load of an intermediary end |
Removal of the capture of direction of the load of launch of union
|
|
1 - Ford's adaptation special 16.040
|
Type of the left side of the transmission
|
|
1 - pin of a cork of transfer of a support,
2 - cork of selector's cork,
3 - switch of fires of a support,
4 - dispatch the pin of the fixation of an axle of a wheel of intermediary gear of the transfer of a support,
5 - behind I set pins of fixation of an axle of a wheel of intermediary gear of transfer of a support |
Removal of a flange of a secondary end through an artist of streaptise
Prevention
 After being demolished of the transmission it is necessary to substitute the whole spring lock rings in the new with the thickness that supplies the necessary values of an axial slit of the elements established with his help. It is necessary to substitute all the rings of fighter also.
The transmission elements (end, loads, sincronizadores, the mechanism of dislocation of gear, etc.) install in two cases that are informed between them. The first one of them located more near to motor also contains the union and one calls a case of union (though in his rear part six elements of the transmission are installed); they call other a case of transmission (though it does not contain all the elements of this knot).
| ORDER OF REALIZATION |
| 1. To fuse the oil of the transmission. |
| 2. To withdraw the load of launch and the forks of the extinguishment of the union of a case of the union. |
|
3. To register a flange of the connection of the advanced hinge of the driving axle and to unscrew a nut of the fixation of a flange through the drawing of easy punches to a key (1 – the device to blockade of a flange, 2 – a flange of hinge). |
| 4. Through Ford's adaptation 16.040 to withdraw the capture of direction of the load of launch of the union. |
| 5. To withdraw an internal spring ring of a main end. |
| 6. To withdraw a plate of the fixation of a nut of the load of an intermediary end (to see the rice. Vision of front of case of union). |
| 7. Through a 17 mm key to unscrew a nut of the load of an intermediary end. |
| 8. For a side a case to unscrew pins (type of Torx) of a cork of the transfer of a support (to see the rice. Type of the left side of the transmission). |
| 9. For a side a case in order that (2) corks of the selector to unscrew a cork and to take one spring, an empurrador, the capture and a ball of a cork of the selector. |
| 10. (3) fires of a support unscrew the switch. |
| 11. To unscrew two pins (4 and 5) of the fixation of an axle of a wheel of intermediary gear of the transfer of a support and to take only an advanced pin (4). |
| 12. To unscrew ten pins of the connection of a case of the union with a case of transmission. |
| 13. Through two screwdrivers it is careful to divide both parts of a case of the transmission. |
|
14. To withdraw a case of union of a case of transmission; in case of the necessity of 16.041 uses the adaptation. |
| 15. To withdraw an axle of forks (1) (to see the rice. Mechanism of dislocation of gear, MT 75 transmissions) of 3-4 transfers, 5th transfer and transfer of a support. |
| 16. To take a rear pin (5) (to see the rice. Type of the left side of the transmission) of fixation of an axle of a wheel of intermediary gear of transfer of a support. |
|
17. Of a case of the transmission to take a magneto. |
| 18. Through the artist of streaptise correspondent to withdraw a flange of the connection of the advanced hinge of the driving axle of a secondary end (to see the rice. Removal of a flange of a secondary end through an artist of streaptise). |
|
19. To take a ring of fighter of a secondary end. |
|
20. To withdraw a wheel of gear of driving of a speedometer and the remote capture. |
|
21. To stretch out of a transmission they fit in a secondary end through an artist of streaptise. |
|
|
|
