FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+ 6. Union
- 7. Transmissions
   +7.1. Mechanical transmission of five speeds of type of N
   -7.2. Mechanical MT 75 transmission
      7.2.1. Technical characteristic
      -7.2.2. Service and repair
         7.2.2.1. Removal and installation of the transmission
         +7.2.2.2. Desmontagem of the transmission
         7.2.2.3. Meeting of the transmission
   +7.3. Transmission A4LD automatic
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

7.2.2. Service and repair

7.2.2.1. Removal and installation of the transmission

GENERAL INFORMATION

MT 75 transmission

Pin of fixation of the transmission to a ray

The pin of the fixation is specified by an arrow.

Ring of lock of fixation of the walk of a speedometer

The lock ring is specified by an arrow.

Removal

ORDER OF REALIZATION

1. For desconectar they connect a weight of the accumulator.

2. To withdraw the gear that moves doorknob of lever.

3. To withdraw (when the middle consolation or the shelf are depending on the version of the equipment) on the lever of dislocation of gear.

4. To withdraw an extern covering of the lever of the gear that he moves after a lack of interest of the bearer, and also an internal covering with the bearer after unscrewing of a frame of the bearer of the tunnel of floor.

5. To unscrew the lever of dislocation of gear of a rear part of a case of the transmission.

6. To support a pedal of union.

7. In a driving compartment to withdraw the advanced left and right acoustic isolation.

8. To withdraw the superior covering of an electric heater.

9. To unscrew the superior pin of the fixation of an author and desconectar a weight wire.

10. A monkey supports the motor.

11. Below the car to withdraw the lowest acoustic covering of the motor.

12. Desconectar a metal conector and of rubber of a longitudinal ray.

13. Desconectar an advanced tube of reception of a final collector, having unscrewed the fixation of nuts.

14. Desconectar the driving axle of a flange of the wheel of main gear of the main transfer, maintaining hair clips of hair with the instrument of Torx that were not unscrewed of a flange of the main transfer unscrewing nuts of the fixation of an end, and also desconectar the middle load of the driving axle of an arm of body.

15. Desconectar to elastic union of the driving axle of a flange of the transmission and to take the driving axle.

16. To support the transmission through wooden grindstones and a monkey.

17. To remove the bearer of a support of the triangular form of interruption of the transmission.

18. To lower the transmission.

19. To lower the motor. The head of the cylinder block must not contact to curb oil pipelines at the same time. In case of the necessity it is possible to establish the wooden grindstone between a head of the cylinder block and a splitting frontlet.

20. Desconectar the extern mechanism of the dislocation of gear.

21. Desconectar a thread of a speedometer and a wire of the switch of fires of a support.

22. To take a spring latch and desconectar a thread of union of the union that puts forks out.

23. To withdraw the splitting leaf of a case of the union located between the cylinder block of the motor and the transmission.

24. To unscrew two remained pins of the fixation of an author and to remove an author.

25. To unscrew 3 pins of the fixation of a case of the union to the cylinder block of the motor.

26. Desconectar to transmission of the motor and to take it of below of the car.

Installation

ORDER OF REALIZATION

1. To delay the union that puts forks out behind and to register them a wire in this situation.

2. To cover of a fine layer of the lubricant of special Ford (n ° 5021439) of an opening of a main end.

3. To annex the transmission to the cylinder block of the motor (3 pins).

4. To insert two pins of the fixation of an author in openings.

5. To establish a splitting leaf between the cylinder block of the motor and a case of a box.

6. To hold tight pins of the fixation of a splitting leaf.

7. Then to execute operations in the return sequence regarding the process of removal of the transmission, installment of attention in:
      – observance of the necessary moments of pressure of screwed connections;
      – necessary stuffing of the rising transmission of the corresponding oil;
      – check of tension of the transmission.

Prevention

Before the installation of the elastic hinge of rubber of the driving axle in a flange of the transmission it is necessary to check if the hair hair clips on a flange concentrate correctly. In case of the detection of the fact that the hair hair clips saw it is necessary to unscrew them, to compensate for them his woodcarving, to devote itself in the siege of the woodcarving that is screwed in in a flange, two decreases of the protection of ways of unscrewing (for example, Loctite 270), to hold tight these pins during 5 minutes the moment of 80 nanômetros and to wait for 30 minutes for the hardening condom.