FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+ 6. Union
- 7. Transmissions
   -7.1. Mechanical transmission of five speeds of type of N
      7.1.1. Technical characteristic
      -7.1.2. Service and repair
         7.1.2.1. Removal and installation of the transmission
         7.1.2.2. To be demolished and meeting of the transmission
         7.1.2.3. To be demolished and meeting of the block of wheels of gear
   +7.2. Mechanical MT 75 transmission
   +7.3. Transmission A4LD automatic
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

7.1.2.3. To be demolished and meeting of the block of wheels of gear

GENERAL INFORMATION

Mechanism of dislocation of gear of the transmission of five speeds

1 - management end,
2 - selector,
3 - ring of the spring lock,
4 - forks of 3-4 transfers,
5 - forks of 1-2 transfers,

6 - forks of the 5th transfer,
7 - lever of connection of the reverse gear,
8 - pin of the spring lock,
9 - spring

The internal mechanism of dislocation of gear installed in mechanical transmissions of type of N from October of 1986

1 - the operational end,
2 - control lever,

3 - prick,
4 - armband

DESMONTAGEM OF THE SECONDARY END OF THE TRANSMISSION

Desmontagem of a secondary end

1 - ring fighter,

2 - wheel of gear of the 1st transfer,

3 - ring of the sincronizador of the 1st transfer,

4 - sincronizador of 1-2 transfers

ORDER OF REALIZATION

	1. To withdraw a ring of lock and to move the sincronizador of the third and fourth transfers together with a wheel of gear of the third transfer of an advanced part of a secondary end, use, necessarily, an artist of streaptise. To separate a wheel of gear and the sincronizador, soon to withdraw the ring of sincronização of the third transfer.
	2. To withdraw an extern ring of a wheel of gear of the second transfer, soon to take two adjusts half of rings.
3. To move a wheel of gear of the second transfer for an advanced part of a main end and to withdraw the ring of sincronização of the second transfer.
4. To observe the mutual provision of a nave of the sincronizador of the first and second transfers and the capture one of other and an agreement of flute of fork, soon to move the capture of a nave ahead and to withdraw armbands and springs. The nave of the sincronizador cannot be withdrawn of a secondary end.
	5. To withdraw a speedometer they direct the wheel of gear of a rear part of a secondary end.
6. To withdraw the block of the sincronização of the fifth transfer and the wheel of driven gear of the fifth transfer of a main end.
7. To take the ring of lock considering the load of a secondary end soon to establish a middle case in wooden grindstones and to take a secondary end was seeing the load.
	8. Withdraw a ring, a wheel of gear of the first transfer and a ring of the sincronização of the first transfer.
9. If necessary a lock ring will withdraw and take the load of a middle case, using a metal tube. To withdraw sincronizadores, previously having observed a relative agreement of a nave and the capture. To move the capture of a nave and to withdraw nucleuses of blockade and springs.

MEETING OF THE SECONDARY END

Installation of a wheel of gear of the walk of a speedometer

One adjusts = 123,5 ± 0,5 mm.

ORDER OF REALIZATION

1. Before meeting the oil of the transmission of a surface of the details they interact.
2. In an average part of a case of the transmission to install the load of a secondary end and to fix a ring of lock of this load.
3. To establish the spring touches naves of sincronizadores.
4. To establish a ring of the sincronizador of the 1st transfer and a wheel of gear of the 1st transfer in a secondary end.
5. To establish in a secondary end a ring of fighter for work edges in the direction of the load.
6. To install the load, a secondary end and a lock touch an average part of a case of the transmission.
7. To establish a wheel of gear of the 5th transfer, a ring of fighter and the sincronizador of the 5th transfer in a secondary end.
8. To establish a speedometer they direct the wheel of gear in a secondary end. 123 observes the distance E = ± 0,5 mm (to see the rice. Installation of a wheel of gear of the walk of a speedometer).
9. To install the sincronizador of 1-2 transfers in a secondary end. The flute (for forks) in the unstable union of this sincronizador has to address ahead.
	10. To establish a ring of sincronizador, a wheel of gear of the 2nd transfer and two adjusts half of rings and a ring of lock. The initial agreement for the persistent half of the rings of the second transfer is specified by an arrow.
	11. To establish a wheel of gear of the 3rd transfer, the sincronizador of 3-4 transfers and a lock touch a secondary end.
12. If the sincronizador understood, then in his meeting there is necessary pay the attention that the flute in the unstable union addressed ahead.

TO BE DEMOLISHED AND MEETING OF THE BLOCK OF WHEELS OF GEAR OF THE INTERMEDIARY END

ORDER OF REALIZATION

The desmontagem of the block of wheels of gear of an intermediary end does not represent special difficulties. There are necessary needle loads pay attention to the loss of a needle of loads and remote captures (ahead and behind). In the meeting it is necessary to install carefully two remote captures and to cover needles of loads with the gooey lubricant of which they were not withdrawn in the course of the installation of an end of the block of wheels of gear.