FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car

Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+ 6. Union
- 7. Transmissions
   -7.1. Mechanical transmission of five speeds of type of N
      7.1.1. Technical characteristic
      -7.1.2. Service and repair
         7.1.2.1. Removal and installation of the transmission
         7.1.2.2. To be demolished and meeting of the transmission
         7.1.2.3. To be demolished and meeting of the block of wheels of gear
   +7.2. Mechanical MT 75 transmission
   +7.3. Transmission A4LD automatic
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment

7.1.2.2. To be demolished and meeting of the transmission

GENERAL INFORMATION

Wheels of gear and end of the transmission

1 - lock the ring,
2 - lock the ring,
3 - load gives ball,
4 - main end,
5 - the radial roll that is patient with rolls of needle and two rings,
6 - ring of sincronização,
7 - the spring of fixation,
8 - sincronizador of third / quarter of transfers,
9 - wheel of gear of the third transfer,
10 - persistent rings half,
10th – a ring of lock of persistent half of rings,
11 - wheel of gear of the second transfer,
12 - a main end with the sincronizador,
13 - wheel of gear of the first transfer,
14 - ring that preserves the oil,
15 - wheel of gear of the fifth transfer,

16 - sincronizador of the fifth transfer,
17 - nave of the sincronizador of a wheel of gear of the fifth transfer,
18 - speedometer walk,
19 - taken of expansion,
20 - needle rolls,
21 - wheels of gear of an intermediary end,
22 - roll load,
23 - lavador,
24 - wheel of gear of the fifth transfer,
25 - lavador,
26 - nut,
27 - intermediary end,
28 - wheel of intermediary gear of the reverse gear,
29 - taken,
30 - intermediary end.

Desmontagem

ORDER OF REALIZATION

1. To compensate for the surface of the kerosene of transmission and to dry they rub it.
2. To withdraw the load of the extinguishment of the union together with the lever.
	3. To unscrew and to withdraw the switch of lamps of a support.
	4. To unscrew pins of the fixation of a case of the union (they are specified by firearms) and to withdraw it.
5. To unscrew pins and to withdraw the capture of direction of the load of the extinguishment of the union with the placing of the advanced party of the transmission.
	6. To unscrew pins of the fixation and to withdraw the superior covering with the placing. The arrow showed an agreement of spring locks of the care of the included transfer.
	7. To unscrew pins and to take a plate of lock of a wheel of gear of the 5th transfer of a rear case.
8. To take of a few back they fit in a spring of lock with an armband of a fork of the inclusion of the 5th transfer.
9. Through an opening of the lever of dislocation of gear through the screwdriver to beat a rear cape of a rear case.
	10. To light the reverse gear and to move an axle of the lever of the choice of transfers behind. To establish an axle in the wooden grindstone, soon to take a pin of roll of the fixation of the selector and to withdraw a conector of the rear end of a stick of the choice of transfers.
11. To unscrew pins and to withdraw a rear case.
	12. To discover with back a case and to take a speedometer they direct the wheel of gear.
	13. To establish wheels of gear in the neutral situation then through a key of six sides to unscrew screws of the fixation and to withdraw a hat of an armband of the lever of the choice of transfers for a side of a case of transmission, soon to take one spring and an armband.
14. To take a pin of a nave of the lever of the choice of transfers and of an axle of the lever of the choice of transfers.
	15. To withdraw the spring that allies of an axle of the lever of the choice of transfers and an armband of the 5th transfer. With this finality through the small screwdriver to beat a hat and a pin and to move an armband of an axle of the lever of the choice of transfers.
16. To observe a relative posicionamento of details of the mechanism of the commutation, soon to take an end of a rear part of the transmission, to withdraw the capture of an end and a plate of lock, the forks of the first / second, third / fourth thing transfers, a fork and the transitional capture of the fifth transfer.
	17. To take a ring of lock and to spread out the block of the sincronização of the fifth transfer of the general covering, having left it in a free state in the secondary one to an end. To move the wheel of driven gear of the fifth transfer of a nave of the block of the sincronização of the fifth transfer.
	18. To include at the same time two transfers (to blockade of the transmission) and to unscrew a nut of the fixation of a wheel of gear of the 5th transfer in the intermediary to an end.
19. Through a nucleus to hold tight out an axle of the block of wheels of gear of an intermediary end behind. It is necessary to guard constantly the contact of a nucleus with an axle of the block of wheels of gear of an intermediary end not to allow the loss of needles of the load.
20. To annex the adaptation to an advanced part of a case of the transmission.
	21. 16.033 withdraws a wheel of gear of the 5th transfer of an intermediary end through the adaptation.
22. To insert behind at the ancient place an axle of the block of wheels of gear of an intermediary end, when 16,033 are putting an adaptation of the hand for out axle.
23. To withdraw a ring of lock of the load of the block of wheels of gear in an average part of a case of the transmission.
24. To take the remote capture of the load.
25. To put both transfers out before included.
26. To unscrew the pin maintaining an average part of a case of the transmission in 6-7 mm and to withdraw an average part of a case.
	27. To hold tight the load of the block of wheels of gear deeply in on an average part of a case through two fine screwdrivers (1 and 2 – screwdrivers, 3 – a pin) and to withdraw an extern ring of the load.
28. To move an axle of the block of wheels of gear behind so that it was possible to take the block of wheels of gear of a case.
29. To put the block of wheels of gear of an intermediary end in a bottom of an advanced part of a case of the transmission.
	30. To take a secondary end together with an average part of a case.
	31. To withdraw a main end.
	32. Through the artist of streaptise correspondent (the capture of the great diameter, M8x60 they fire together with a nut) to withdraw an axle of a wheel of intermediary gear of the reverse gear.
33. To take a ring of lock and an axle of the lever of the reverse gear.
	34. To withdraw a magneto of the lowest part of a case of a main end.

Meeting

Before the meeting it is necessary to wash itself out and to check a condition of loads, sincronizadores and gear wheels.

The meeting of the transmission is executed in the return sequence regarding the process of his desmontagem. In the installation time it is necessary to pay attention to the next actions.

ORDER OF REALIZATION

1. To polish with the lubricant of gooey load of a needle of loads of the block of wheels of gear of an intermediary end and it is correct to arrange them in the axle that forms an internal trace of races.
	2. Through the adaptation 16.033 to establish a wheel of gear of the 5th transfer in the intermediary to an end. The remote capture of a wheel of gear will of covered of the lubricant to secure the free rotation of a wheel of gear.
3. The woodcarving of the pins that are crushed in through openings of a case before the installation must be covered of the corresponding selante.
4. Before corseting itself on a rear part of a case of the transmission it is necessary to check the functioning of the transmission (a possibility of the inclusion of separate transfers and free rotation of the end).