FORD'S SCORPIO

1985-1994 of launch

Repair and operation of the car



Ford Skorpio
+1.1. Identification of the car
+2. Maintenance
+3. Motors
+4. System cooling
+5. Fuel system
+ 6. Union
- 7. Transmissions
   -7.1. Mechanical transmission of five speeds of type of N
      7.1.1. Technical characteristic
      -7.1.2. Service and repair
         7.1.2.1. Removal and installation of the transmission
         7.1.2.2. To be demolished and meeting of the transmission
         7.1.2.3. To be demolished and meeting of the block of wheels of gear
   +7.2. Mechanical MT 75 transmission
   +7.3. Transmission A4LD automatic
+8. Driving axle and rear bridge
+9. Direction
+10. Supports of the triangular form of interruption
+11. Brakes system
+12. Wheels and tires
+13. Body
+14. Electric equipment


bfe6b27a


7.1.2. Service and repair

7.1.2.1. Removal and installation of the transmission

GENERAL INFORMATION

Mechanical transmission of five steps of type of N


Case of the mechanical transmission of five speeds

1 - dispatch the part of a case,
2 - average part of a case,
3 - behind it leaves from a case,
4 - covering,
5 - the capture of direction of the load of launch of union,
6 - placing of a case,
7 - switch of fires of a support

ORDER OF REALIZATION
1. To install the car on the observation channel or to lift it in the elevator.
2. For desconectar they connect a weight of the accumulator.
3. In models with motors V6 to withdraw the protected case of the distributor, a covering and a rotor.
4. To unscrew the gear that moves doorknob of lever.
5. To withdraw (when the middle consolation or the shelf are depending on the version of the equipment) on the lever of dislocation of gear.
6. To withdraw an extern covering of the lever of the gear that he moves after a lack of interest of the bearer, and also a covering interns together with the bearer after unscrewing of a frame of the bearer of a tunnel of floor.
7. Desconectar to lever of dislocation of gear of a rear part of a case of the transmission.
8. To lift the car.
9. Desconectar the stabilizer of a longeron.
10. In models with motors V6 to withdraw the thermal filter.
11. Desconectar elements of rubber of a support of the triangular form of interruption of supports of the triangular form of the fixation of a rear part of the final system and to register the whole system so that it does not load the fixation of his advanced part.
12. To unscrew the fixation of the middle load of the driving axle, and also to unscrew fastenings from the driving axle to a flange of the main end of the main transfer on the rear bridge.
13. To take an advanced part of the driving axle of a rear case of the transmission and an opening deadens the corresponding cork in a rear part of a case of the prevention of an effluence of oil of the transmission.
14. Through a monkey for wooden grindstones to support the transmission.
15. To unscrew a crossbeam of the fixation of the transmission to a body. It fixes five pins – two of each party and one in the center.
16. To withdraw a spring hook of the fixation of a thread of the walk of a speedometer and desconectar a thread of the transmission.
17. Desconectar an electric wire of the switch of fires of a support.
18. To remove an author.
19. Desconectar an union thread of putting forks out.
20. To unscrew pins of the fixation of the transmission to an intermediary plate.
21. The motor – the transmission withdraws the lever of jet of the knot.
22. Desconectar to transmission of the motor (six pins) and to take carefully the transmission of bass of the car.

Installation


ORDER OF REALIZATION
1. Quantity of the lubricant covers openings of a main end little with a.
2. The installation of the transmission is executed in the sequence, the return regarding the removal process. After the installation it is necessary to check the level of oil in the transmission.